all ports on the switch are in the same vlan and these ports are working fine. when I try to deconnect hostA from switch and replace it by hostB on the same port, hostB can communicate with hostC (pings are working fine). so i think that the issue come from hostA network config.
I'm pinging IP address and not hostnames
Howto check if a ethernet interface is up?
It's impossible to determine via the ipaddress i have learned, or?
Can someone please give me a hint on howto do?
Environment == Linux x86 GNU GCC.
:D
regards
Esaia (2 Replies)
Installed a replacement 3com pci card on an ibm PC 300 GL, running OpenServer 6.0 , brought up system, and recieved this message:
Fsstat:/dev/boot mounted
Mounted /stand filesystem
System auditing is not enabled.
Dlpid:Unable to open network adapter driver (/dev/mdi/r8e0)
Dlpid:No such... (0 Replies)
Hi all,
Here im facing problem with NIC Interface with my X86 Version of Solaris Express, even after loading module for that Interface. So please check this below mentioned log for your use and get back to me ASAP.
- - - -- --... (0 Replies)
I need to install ethernet card drivers on intel machine. How can i know which Ethernet card interface (sfe,rh,rtls...) is it? How can i know the speed of that card? How can i know network traffic ? If network traffic is more with that interface what should i do?
Thanks in advance (2 Replies)
Hi All,
I want to configure network into my system.
i tried following in to configure the interface
to find the name of interface
#prtdiag |grep net
i got following
0 PCI-1 33 1 network-SUNW, hme
then i tried following
#prtconf -v |grep net
network, instance #0 (6 Replies)
Hi,
During the installation of solaris suppose I am configuring one ethernet interface that is primary but on my server there are 4 ethernet interfaces,because all other interface not configured,
what is way to find out how many ethernet interfaces are there on Server, (6 Replies)
This is my situation
DOS pc serial cable (sl0) Linux Pc eth1
192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router)
I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface.
... (3 Replies)
Hi,
is there any method to check the interface collisions on ethernet NIC in AIX. I know that in Solaris it's netstat -i but I've written that in AIX it doesn't show this.
Thanks®ards,
p (1 Reply)
Hello,
I am trying to set up Channel Bonding on a RHEL6 Virtual Box VM. I have 2 ethernet cards on the machine which are set up in Internal Network mode. I followed all the steps exactly as mentioned in the RHEL6 deployment Guide, but for some reason i think results are not correct. Here are my... (13 Replies)
Hi ,
Could someone let me know how to detect duplicate ip address after assigning ip address to ethernet interface using c program (3 Replies)
Discussion started by: Gopi Krishna P
3 Replies
LEARN ABOUT SUSE
aseqnet
aseqnet(1) General Commands Manual aseqnet(1)NAME
aseqnet - ALSA sequencer connectors over network
SYNOPSIS
aseqnet [remotehost]
DESCRIPTION
aseqnet is an ALSA sequencer client which sends and receives event packets over network. Suppose two hosts connected by network, hostA as
a server and hostB as a client. The ALSA sequencer system must be running on both hosts. For creating the server port, run the following
on hostA:
hostA% aseqnet
sequencer opened: 128:0
Then a user client 128 with port 0 was opened on hostA. (The client number may vary.) For creating the (network-)client port, run aseqnet
with the hostname of the server:
hostB% aseqnet hostA
sequencer opened: 132:0
Now all events sent to hostA:128:0 are transferred to hostB:132:0, and vice versa.
The ports created by aseqnet can be connected arbitrary to other sequencer ports via aconnect(1). For example, to connect hostB:132:0 to a
MIDI output device 65:0:
hostB% aconnect 132:0 65:0
Then events to hostA:128:0 will be delivered to hostB:65:0. The following command plays MIDI on hostB.
hostA% pmidi -p 128:0 foo.mid
The multiple clients may exist simultaneously. If hostC is connected as a client to hostA, events from from hostA are sent to all con-
nected network clients, i.e. hostB and hostC. However, only one connection is allowed from a client to a server.
To disconnect network, stop all clients before server by ctrl-C or sending signal to them. The server will automatically quit.
OPTIONS -p port
Specify the TCP port number or TCP service name.
-s addr
Subscribe to the given address for read automatically.
-d addr
Subscribe to the given address for write automatically.
-v Verbose mode.
SEE ALSO aconnect(1), pmidi(1)AUTHOR
Takashi Iwai <tiwai@suse.de>.
January 1, 2000 aseqnet(1)