Do you know the gateway address for the 10.6.0.x range? It will have to be between zero and 63 with that netmask.
Have a look at the file ifcfg-eth0 or ifcfg-eth1 and you will see the difference. When you do, add a line in ifcfg-eth2 like this:-
.... and restart the ethernet card:-
As you will notice, this will cut access whilst you do it. Make sure you are connected to either the console, or the other network card.
Howto check if a ethernet interface is up?
It's impossible to determine via the ipaddress i have learned, or?
Can someone please give me a hint on howto do?
Environment == Linux x86 GNU GCC.
:D
regards
Esaia (2 Replies)
Installed a replacement 3com pci card on an ibm PC 300 GL, running OpenServer 6.0 , brought up system, and recieved this message:
Fsstat:/dev/boot mounted
Mounted /stand filesystem
System auditing is not enabled.
Dlpid:Unable to open network adapter driver (/dev/mdi/r8e0)
Dlpid:No such... (0 Replies)
Hi all,
Here im facing problem with NIC Interface with my X86 Version of Solaris Express, even after loading module for that Interface. So please check this below mentioned log for your use and get back to me ASAP.
- - - -- --... (0 Replies)
I need to install ethernet card drivers on intel machine. How can i know which Ethernet card interface (sfe,rh,rtls...) is it? How can i know the speed of that card? How can i know network traffic ? If network traffic is more with that interface what should i do?
Thanks in advance (2 Replies)
Hi All,
I want to configure network into my system.
i tried following in to configure the interface
to find the name of interface
#prtdiag |grep net
i got following
0 PCI-1 33 1 network-SUNW, hme
then i tried following
#prtconf -v |grep net
network, instance #0 (6 Replies)
Hi,
During the installation of solaris suppose I am configuring one ethernet interface that is primary but on my server there are 4 ethernet interfaces,because all other interface not configured,
what is way to find out how many ethernet interfaces are there on Server, (6 Replies)
This is my situation
DOS pc serial cable (sl0) Linux Pc eth1
192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router)
I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface.
... (3 Replies)
Hi,
is there any method to check the interface collisions on ethernet NIC in AIX. I know that in Solaris it's netstat -i but I've written that in AIX it doesn't show this.
Thanks®ards,
p (1 Reply)
Hello,
I am trying to set up Channel Bonding on a RHEL6 Virtual Box VM. I have 2 ethernet cards on the machine which are set up in Internal Network mode. I followed all the steps exactly as mentioned in the RHEL6 deployment Guide, but for some reason i think results are not correct. Here are my... (13 Replies)
Hi ,
Could someone let me know how to detect duplicate ip address after assigning ip address to ethernet interface using c program (3 Replies)
Discussion started by: Gopi Krishna P
3 Replies
LEARN ABOUT SUSE
smpppd-ifcfg
SMPPPD-IFCFG(8) SMPPPD SMPPPD-IFCFG(8)NAME
smpppd-ifcfg - SuSE Meta PPP Daemon
DESCRIPTION
smpppd-ifcfg is a daemon that controls a single dialup connection to the internet. It does so by starting and controlling the pppd. The
configuration of the dialup connections is done by YaST2.
smpppd-ifcfg is not intended for direct use. Use ifup and ifdown or a frontend like cinternet , qinternet or kinternet instead.
OPTIONS
These options are recognized by smpppd-ifcfg. If a long option shows an argument as mandatory, then it is mandatory for the equivalent
short option also.
--up Bring the connection up. This is the default action.
--down Bring the connection down.
--status
Report status of the connection.
-i, --ifcfg=NAME
Specify the ifcfg file to use. This option is mandatory.
-p, --provider=NAME
Specify the provider file to use.
--detach
Detach from the controlling terminal. This is the default.
--nodeatch
Don't detach from the controlling terminal.
-d, --debug
Turn on debugging.
--version
Show program version and exit.
--help Show help information and exit.
FILES
/etc/sysconfig/network/ifcfg-*
Configuration files for the interfaces.
/etc/sysconfig/network/providers/*
Configuration files for the providers.
/var/log/smpppd/ifcfg-xxx.log
Log file.
/var/log/smpppd/accounting.log
File containing accounting information.
/var/run/smpppd.ifcfg-xxx.pid
Pid file.
/var/lib/smpppd/ifcfg-xxx.info
Info file with various status information.
/var/run/smpppd/ifcfg-xxx
Socket to communicate with smpppd.
SEE ALSO
kinternet, qinternet, cinternet(1), accounting(1), wvdial(1), smpppd.conf(5), pppd(8), smpppd(8).
AUTHOR
Arvin Schnell <arvin@suse.de>
SuSE December 2002 SMPPPD-IFCFG(8)