Do you know the gateway address for the 10.6.0.x range? It will have to be between zero and 63 with that netmask.
Have a look at the file ifcfg-eth0 or ifcfg-eth1 and you will see the difference. When you do, add a line in ifcfg-eth2 like this:-
.... and restart the ethernet card:-
As you will notice, this will cut access whilst you do it. Make sure you are connected to either the console, or the other network card.
Howto check if a ethernet interface is up?
It's impossible to determine via the ipaddress i have learned, or?
Can someone please give me a hint on howto do?
Environment == Linux x86 GNU GCC.
:D
regards
Esaia (2 Replies)
Installed a replacement 3com pci card on an ibm PC 300 GL, running OpenServer 6.0 , brought up system, and recieved this message:
Fsstat:/dev/boot mounted
Mounted /stand filesystem
System auditing is not enabled.
Dlpid:Unable to open network adapter driver (/dev/mdi/r8e0)
Dlpid:No such... (0 Replies)
Hi all,
Here im facing problem with NIC Interface with my X86 Version of Solaris Express, even after loading module for that Interface. So please check this below mentioned log for your use and get back to me ASAP.
- - - -- --... (0 Replies)
I need to install ethernet card drivers on intel machine. How can i know which Ethernet card interface (sfe,rh,rtls...) is it? How can i know the speed of that card? How can i know network traffic ? If network traffic is more with that interface what should i do?
Thanks in advance (2 Replies)
Hi All,
I want to configure network into my system.
i tried following in to configure the interface
to find the name of interface
#prtdiag |grep net
i got following
0 PCI-1 33 1 network-SUNW, hme
then i tried following
#prtconf -v |grep net
network, instance #0 (6 Replies)
Hi,
During the installation of solaris suppose I am configuring one ethernet interface that is primary but on my server there are 4 ethernet interfaces,because all other interface not configured,
what is way to find out how many ethernet interfaces are there on Server, (6 Replies)
This is my situation
DOS pc serial cable (sl0) Linux Pc eth1
192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router)
I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface.
... (3 Replies)
Hi,
is there any method to check the interface collisions on ethernet NIC in AIX. I know that in Solaris it's netstat -i but I've written that in AIX it doesn't show this.
Thanks®ards,
p (1 Reply)
Hello,
I am trying to set up Channel Bonding on a RHEL6 Virtual Box VM. I have 2 ethernet cards on the machine which are set up in Internal Network mode. I followed all the steps exactly as mentioned in the RHEL6 deployment Guide, but for some reason i think results are not correct. Here are my... (13 Replies)
Hi ,
Could someone let me know how to detect duplicate ip address after assigning ip address to ethernet interface using c program (3 Replies)
Discussion started by: Gopi Krishna P
3 Replies
LEARN ABOUT SUSE
ifcfg-bonding
IFCFG-BONDING(5) Network configuration IFCFG-BONDING(5)NAME
ifcfg-bonding - interface bonding configuration
SYNOPSIS
/etc/sysconfig/network/ifcfg-bond*
Bonding Interfaces
To setup a bonding interface you need a configuration file ifcfg-bond<X> with the usual network settings. But you must add additional vari-
ables
BONDING_MASTER
must be set to 'yes' to identify this interface as a bonding interface
BONDING_SLAVE_<X>
here you specify the interface name representing the slave network interfaces.
BONDING_MODULE_OPTS
contains bonding options. Here you can set interface timeouts or working modes ('mode=active-backup' for backup mode). For addi-
tional information take a look into the documentation mentioned at the bottom. Note, that this options are not passed as parameters
to the bonding kernel module any more, but set via sysfs interface. This variable will be renamed in the feature.
BONDING_SKIP_REMOVE_WORKAROUND
When set to "yes", a bonding interface will be not removed while ifdown any more to avoid problems, e.g. when some third party ker-
nel module, such as Veritas 'llt' module, does not react correctly to the UNREGISTER event and does not remove its references to the
bonding interface causing all network related operation to stuck.
Note: the bonding options are not reverted when this option is enabled and it is required to either explicitly keep the old options
and set them to their default setting on bonding configuration changes or to reboot.
Example
Example for a bonding interface on eth0 and eth1 using the backup mode
ifcfg-bond0
STARTMODE='onboot'
BOOTPROTO='static'
IPADDR='192.168.0.1/24'
BONDING_MASTER='yes'
BONDING_SLAVE_0='eth0'
BONDING_SLAVE_1='eth1'
BONDING_MODULE_OPTS='mode=active-backup miimon=100'
Additional Information
For additional and more general information take a look into /usr/src/linux/Documentation/networking/bonding.txt. Maybe you need to
install the kernel sources to get this additional documentation.
The configuration of routes for this kind of interface does not differ from ordinary interfaces. See man routes for details.
BUGS
Please report bugs at <http://www.suse.de/feedback>
AUTHOR
Christian Zoz <zoz@suse.de> -- ifup script
Wilken Gottwalt <wgottwalt@suse.de> -- ifcfg-bonding manual page
SEE ALSO ifcfg(5), ifup(8).
sysconfig April 2005 IFCFG-BONDING(5)