02-18-2014
Since you are using the IP only there is no need to modify /etc/hosts... Each interface should normally have a default gateway set...
10 More Discussions You Might Find Interesting
1. Programming
Howto check if a ethernet interface is up?
It's impossible to determine via the ipaddress i have learned, or?
Can someone please give me a hint on howto do?
Environment == Linux x86 GNU GCC.
:D
regards
Esaia (2 Replies)
Discussion started by: Esaia
2 Replies
2. SCO
Installed a replacement 3com pci card on an ibm PC 300 GL, running OpenServer 6.0 , brought up system, and recieved this message:
Fsstat:/dev/boot mounted
Mounted /stand filesystem
System auditing is not enabled.
Dlpid:Unable to open network adapter driver (/dev/mdi/r8e0)
Dlpid:No such... (0 Replies)
Discussion started by: tazmss1
0 Replies
3. Solaris
Hi all,
Here im facing problem with NIC Interface with my X86 Version of Solaris Express, even after loading module for that Interface. So please check this below mentioned log for your use and get back to me ASAP.
- - - -- --... (0 Replies)
Discussion started by: baraghun
0 Replies
4. Solaris
I need to install ethernet card drivers on intel machine. How can i know which Ethernet card interface (sfe,rh,rtls...) is it? How can i know the speed of that card? How can i know network traffic ? If network traffic is more with that interface what should i do?
Thanks in advance (2 Replies)
Discussion started by: younus_syed
2 Replies
5. Solaris
Hi All,
I want to configure network into my system.
i tried following in to configure the interface
to find the name of interface
#prtdiag |grep net
i got following
0 PCI-1 33 1 network-SUNW, hme
then i tried following
#prtconf -v |grep net
network, instance #0 (6 Replies)
Discussion started by: kumarmani
6 Replies
6. Solaris
Hi,
During the installation of solaris suppose I am configuring one ethernet interface that is primary but on my server there are 4 ethernet interfaces,because all other interface not configured,
what is way to find out how many ethernet interfaces are there on Server, (6 Replies)
Discussion started by: manoj.solaris
6 Replies
7. IP Networking
This is my situation
DOS pc serial cable (sl0) Linux Pc eth1
192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router)
I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface.
... (3 Replies)
Discussion started by: mghis
3 Replies
8. AIX
Hi,
is there any method to check the interface collisions on ethernet NIC in AIX. I know that in Solaris it's netstat -i but I've written that in AIX it doesn't show this.
Thanks®ards,
p (1 Reply)
Discussion started by: pitmod
1 Replies
9. IP Networking
Hello,
I am trying to set up Channel Bonding on a RHEL6 Virtual Box VM. I have 2 ethernet cards on the machine which are set up in Internal Network mode. I followed all the steps exactly as mentioned in the RHEL6 deployment Guide, but for some reason i think results are not correct. Here are my... (13 Replies)
Discussion started by: Rohit Bhanot
13 Replies
10. UNIX for Advanced & Expert Users
Hi ,
Could someone let me know how to detect duplicate ip address after assigning ip address to ethernet interface using c program (3 Replies)
Discussion started by: Gopi Krishna P
3 Replies
RARPD(8) System Manager's Manual RARPD(8)
NAME
rarpd - reverse address resolution protocol daemon
SYNOPSIS
rarpd [-v] [-i interface ]
DESCRIPTION
Rarpd listens on the ethernet for broadcast packets asking for reverse address resolution. These packets are sent by hosts at boot time to
find out their IP address. Rarpd looks up the six octet ethernet number in the ethers map finding a host name. This name is translated to
the IP address of the host by a DNS lookup. The IP address is then sent to the host.
Before rarpd can start its service it first finds out what the IP address and hardware address of the ethernet is.
Warning! Sun diskless workstations assume that the first RARP server that answers is the host they are to boot from. For this to work all
other Sun RARP servers delay their answer if they are not also the requestors boot server. This rarpd does not have this kludge so it will
happily engage the Sun boot server to see who can answer the client first. Unless your host can actually serve a Sun diskless client, it
is better not to list any more hosts in the ethers file than necessary.
OPTIONS
-v Be verbose. Show requests which the daemon is responding to.
-i Bind to the named interface. By default rarpd binds to the default interface for the local system type, if available.
SEE ALSO
ifconfig(8), ethers(5), hosts(5),
AUTHOR
Derrick J. Brashear (shadow@dementia.org)
The man page is mostly from the Minix version, by Kees J. Bot (kjb@cs.vu.nl)
RARPD(8)