02-18-2014
yes it's eth2, and I ping from the same network (10.6.0.0)
10 More Discussions You Might Find Interesting
1. Programming
Howto check if a ethernet interface is up?
It's impossible to determine via the ipaddress i have learned, or?
Can someone please give me a hint on howto do?
Environment == Linux x86 GNU GCC.
:D
regards
Esaia (2 Replies)
Discussion started by: Esaia
2 Replies
2. SCO
Installed a replacement 3com pci card on an ibm PC 300 GL, running OpenServer 6.0 , brought up system, and recieved this message:
Fsstat:/dev/boot mounted
Mounted /stand filesystem
System auditing is not enabled.
Dlpid:Unable to open network adapter driver (/dev/mdi/r8e0)
Dlpid:No such... (0 Replies)
Discussion started by: tazmss1
0 Replies
3. Solaris
Hi all,
Here im facing problem with NIC Interface with my X86 Version of Solaris Express, even after loading module for that Interface. So please check this below mentioned log for your use and get back to me ASAP.
- - - -- --... (0 Replies)
Discussion started by: baraghun
0 Replies
4. Solaris
I need to install ethernet card drivers on intel machine. How can i know which Ethernet card interface (sfe,rh,rtls...) is it? How can i know the speed of that card? How can i know network traffic ? If network traffic is more with that interface what should i do?
Thanks in advance (2 Replies)
Discussion started by: younus_syed
2 Replies
5. Solaris
Hi All,
I want to configure network into my system.
i tried following in to configure the interface
to find the name of interface
#prtdiag |grep net
i got following
0 PCI-1 33 1 network-SUNW, hme
then i tried following
#prtconf -v |grep net
network, instance #0 (6 Replies)
Discussion started by: kumarmani
6 Replies
6. Solaris
Hi,
During the installation of solaris suppose I am configuring one ethernet interface that is primary but on my server there are 4 ethernet interfaces,because all other interface not configured,
what is way to find out how many ethernet interfaces are there on Server, (6 Replies)
Discussion started by: manoj.solaris
6 Replies
7. IP Networking
This is my situation
DOS pc serial cable (sl0) Linux Pc eth1
192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router)
I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface.
... (3 Replies)
Discussion started by: mghis
3 Replies
8. AIX
Hi,
is there any method to check the interface collisions on ethernet NIC in AIX. I know that in Solaris it's netstat -i but I've written that in AIX it doesn't show this.
Thanks®ards,
p (1 Reply)
Discussion started by: pitmod
1 Replies
9. IP Networking
Hello,
I am trying to set up Channel Bonding on a RHEL6 Virtual Box VM. I have 2 ethernet cards on the machine which are set up in Internal Network mode. I followed all the steps exactly as mentioned in the RHEL6 deployment Guide, but for some reason i think results are not correct. Here are my... (13 Replies)
Discussion started by: Rohit Bhanot
13 Replies
10. UNIX for Advanced & Expert Users
Hi ,
Could someone let me know how to detect duplicate ip address after assigning ip address to ethernet interface using c program (3 Replies)
Discussion started by: Gopi Krishna P
3 Replies
ping(8) System Manager's Manual ping(8)
Name
ping - send ICMP ECHO_REQUEST packets to network hosts
Syntax
/etc/ping [ options ] host [ datasize [ npackets ]]
Description
The DARPA Internet is a large and complex network of hardware connected together by gateways. The command utilizes the ICMP protocol's
mandatory ECHO_REQUEST datagram to elicit an ICMP ECHO_RESPONSE from a host or gateway. ECHO_REQUEST datagrams (pings) have an IP and ICMP
header, followed by a struct timeval, and then an arbitrary number of pad bytes used to fill out the packet. The length of the default
datagram 64 bytes, but this may be changed using the command-line option.
Typing ``ping host'' without any options will either report ``host is alive'' or ``no answer from host''. To get more statistics use the
-l option or one of the other options.
When using for fault isolation, it should first be run on the local host to verify that the local network interface is up and running.
Then, hosts and gateways further and further away should be pinged. The command with options sends one datagram per second and prints one
line of output for every ECHO_RESPONSE returned. No output is produced if there is no response. If an optional npackets is given, only
that number of requests is sent. Round-trip times and packet loss statistics are computed. When all responses have been received or the
program times out with npackets specified, or if the program is terminated with a SIGINT, a brief summary is displayed.
Options
-d Turns on SO_DEBUG flag on the socket.
-l Gives more statistics than if is used without options. Long output.
-r Bypasses the normal routing tables and sends directly to a host on an attached network. If the host is not on a directly-attached
network, an error is returned. This option can be used to ping a local host through an interface that has no route through it. For
example, after the interface was dropped by
-v Lists ICMP packets other than ECHO RESPONSE that are received. Verbose output.
Restrictions
This program is intended for use in network testing, measurement, and management. It should be used primarily for manual fault isolation.
Because of the load it could impose on the network, it is unwise to use during normal operations or from automated scripts.
See Also
netstat(1), ifconfig(8c)
ping(8)