02-18-2014
Well, there is no eth1. All the other NICs have traffic shown for RX and TX. If you are talking about eth2, have you checked the routing settings or do you ping from the same network?
10 More Discussions You Might Find Interesting
1. Programming
Howto check if a ethernet interface is up?
It's impossible to determine via the ipaddress i have learned, or?
Can someone please give me a hint on howto do?
Environment == Linux x86 GNU GCC.
:D
regards
Esaia (2 Replies)
Discussion started by: Esaia
2 Replies
2. SCO
Installed a replacement 3com pci card on an ibm PC 300 GL, running OpenServer 6.0 , brought up system, and recieved this message:
Fsstat:/dev/boot mounted
Mounted /stand filesystem
System auditing is not enabled.
Dlpid:Unable to open network adapter driver (/dev/mdi/r8e0)
Dlpid:No such... (0 Replies)
Discussion started by: tazmss1
0 Replies
3. Solaris
Hi all,
Here im facing problem with NIC Interface with my X86 Version of Solaris Express, even after loading module for that Interface. So please check this below mentioned log for your use and get back to me ASAP.
- - - -- --... (0 Replies)
Discussion started by: baraghun
0 Replies
4. Solaris
I need to install ethernet card drivers on intel machine. How can i know which Ethernet card interface (sfe,rh,rtls...) is it? How can i know the speed of that card? How can i know network traffic ? If network traffic is more with that interface what should i do?
Thanks in advance (2 Replies)
Discussion started by: younus_syed
2 Replies
5. Solaris
Hi All,
I want to configure network into my system.
i tried following in to configure the interface
to find the name of interface
#prtdiag |grep net
i got following
0 PCI-1 33 1 network-SUNW, hme
then i tried following
#prtconf -v |grep net
network, instance #0 (6 Replies)
Discussion started by: kumarmani
6 Replies
6. Solaris
Hi,
During the installation of solaris suppose I am configuring one ethernet interface that is primary but on my server there are 4 ethernet interfaces,because all other interface not configured,
what is way to find out how many ethernet interfaces are there on Server, (6 Replies)
Discussion started by: manoj.solaris
6 Replies
7. IP Networking
This is my situation
DOS pc serial cable (sl0) Linux Pc eth1
192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router)
I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface.
... (3 Replies)
Discussion started by: mghis
3 Replies
8. AIX
Hi,
is there any method to check the interface collisions on ethernet NIC in AIX. I know that in Solaris it's netstat -i but I've written that in AIX it doesn't show this.
Thanks®ards,
p (1 Reply)
Discussion started by: pitmod
1 Replies
9. IP Networking
Hello,
I am trying to set up Channel Bonding on a RHEL6 Virtual Box VM. I have 2 ethernet cards on the machine which are set up in Internal Network mode. I followed all the steps exactly as mentioned in the RHEL6 deployment Guide, but for some reason i think results are not correct. Here are my... (13 Replies)
Discussion started by: Rohit Bhanot
13 Replies
10. UNIX for Advanced & Expert Users
Hi ,
Could someone let me know how to detect duplicate ip address after assigning ip address to ethernet interface using c program (3 Replies)
Discussion started by: Gopi Krishna P
3 Replies
dceping(8) dceping(8)
NAME
dceping - test the ability to contact DCE services from a local DCE client.
SYNOPSIS
dceping [-n number] [-s time] [-v] [-C] [service_name ...] required to specify the literal strings, NAMESPACE or STRING_BINDING (see nond-
cesvc(4)).
OPTIONS
-n number Specify the number of pinging cycles. Each service is tested once per cycle. The default is one pinging cycle. Specifying -n 0
makes pinging continuous.
-s time Specify time, in seconds, to wait between pinging cycles. You must specify more than one pinging cycle with the -n option in
order to use -s.
-v Run in verbose mode.
-C Ping only core DCE services. This option is ineffective if a service_name is specified on the command line.
DESCRIPTION
dceping verifies that a local DCE client can communicate with DCE and other services. It uses the RPC management interface to determine if
the DCE service is listening. The core DCE services that dceping checks include secd, cdsd, gdad, rpcd, cdsadv, dtsd, and sec_clientd.
You can ping other DCE and non-DCE services by naming them in the file, /opt/dcelocal/hpadmin/etc/nondcesvc. If you want to determine at
run time what services you want dceping to ping, you may do so using the same file. See the manpage, nondcesvc(4), for more information.
You may specify the services to ping on the command line separated by blanks. In this case, dceping does not ping any DCE core services or
the services listed in /opt/dcelocal/hpadmin/etc/nondcesvc. The service_name specified could be either a name in the DCE Cell Directory
Service Namespace or an RPC string binding. It is not
AUTHOR
dceping was developed by HP.
FILES
/opt/dcelocal/hpadmin/etc/nondcesvc
/opt/dcelocal/hpadmin/etc/wellknownif
SEE ALSO
nondcesvc(4), wellknownif(4)
HP DCE
dceping(8)