How to specify local boot up disk in CD boot Grub?
Hi Solaris 10 Experts,
I am wondering what is the correct syntax to edit in Grub when trying to specify the local ZFS boot disk while booting up from a Solaris 10 x86 64bits DVD installation disk. In other word, I try to boot up from local disk without removing the Solaris installation disk from drive which is down in a locked up data center. Below is what the current Grub setting is:
However, I have tried the following changes without success:
I would also like to find out where the current Grub boot up file is located in order to see what is the correct boot up device is in /boot/grub/menu.lst which gives nothing useful:
The filesystem on this server is as follows:
As always, your valuable advice would be much appreciated.
Many thanks again,
George
Last edited by gjackson123; 02-14-2014 at 02:56 AM..
I have installed Linux 7.2 on a IBM xseries 235 server with 5 scsi hard drives and ServerRaid-5i Ultra320 scsi controller.
I started my installation by configuring the raid controller. I created 2 arrays, raid 1 and raid5. I then proceeded to install Linux and load the drivers.
After the... (2 Replies)
I have an issue with booting NTFS partitions with Grub.
I have two HHD
1st HDD with Red Hat 9.0 and Grub as bootloader
2nd HDD with 8 Win partitions all ntfs.
I have added the following line in my grub.conf:
title Windows2000/Domino 6
root (hd1,0)
makeactive
chainloader +1
When I... (4 Replies)
Hi!
I got some serious problems with booting the computer. When started it prints GRUB GRUB GRUB all over the screen. tchan on #grub tried to help me but with no result. Here is the log.
Mabey there is something that we have missed?:confused: (3 Replies)
my redhat 9 will not boot. We had a power failure and when the power came back, my redhat linux will not boot.
The machine come up to grub prompt.
I tried the following from grub prompt
root (hd0, then press tab key
partition num:0 filesystem type unknown, partition type 0x83... (7 Replies)
Hello,
I'm working on a x86 machine with 3 disks installed. I need to boot from disk to disk, but I cannot figure out how to do this using Grub. The O/S is Solaris 10 and grub version is 0.95
Can anyone give me any help with this?
Thanks,
James. (0 Replies)
Hello,
I am using debian-5.0.0(lenny) . I installed windows xp(a hacked version) on a usb stick. this stick works perfectly well and boots off a windows system successfully.
but on linux it is finding problems to do so.
So I finally decided to put a grub entry to boot off the usb HDD.
... (8 Replies)
I am trying to install Solaris x86 using the Jumpstart server. I run the add_install_client command with appropriate options, and reboot my x86 Target box. The installation starts fine and unattended. After the installation completes and the target goes for a re-boot, it does not boot from the HDD... (9 Replies)
Hi,
i am running an old Opensolaris 5.11 snv_111b on an x86 server. After almost 4 years of successful service, last night out of the blue started to refuse all connections to it's services, ssh, http,etc. The only visible solution at that time was a restart. But now instead of booting the... (2 Replies)
Hi, someone knows how can I boot my OS or cdrom from a Grub Minimal_Bash? :confused: sorry, I´m a dummy
I explain, when I start loading the OS, I get errors, and ends up in the grub bash. This is the minimal_bash and I have no idea of any command. It tells me "unknow partition". The problem is... (0 Replies)