02-12-2014
[Solved] Redhat system is not booting in GUI mode
Hi Guys
Required help in Redhat 6.1.
After installation of Redhat 6.1 in VMware system is not going in GUI mode.
please to solve the issue...
Thanks...
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
When I created the redhat installation, I configured it to boot directly into GNOME, but now I want it to boot into the shell login screen. How can I change that?
Thanks. (1 Reply)
Discussion started by: dangral
1 Replies
2. UNIX for Dummies Questions & Answers
i have the Redhat installed in this Hard Drive and i wanna use it in this old computer of mine.. it works fine in my new computer.. but when i put it in my old one.. which is.. P1 150MHz 32MBramz it wont load the kernal and keeps on restarting the computer.. keeps on goin like this.. i get the GRUB... (2 Replies)
Discussion started by: dezithug
2 Replies
3. Solaris
I had a power failure the other day and when my relatively new Solaris 10 machine rebooted it is thrown into maintenance mode.
I've found the following lines in the /var/adm/messages file, I'm assuming this is the root cause of the problem. However, I don't have the slightest idea on how to... (9 Replies)
Discussion started by: cheetobandito
9 Replies
4. HP-UX
I think that if the directory /tcb exists, HP-UX is in trusted mode and the passwd data is somewhere in /tcb/files/auth. But that's all I remember.
Also I think recent versions of HP-UX can have a /etc/shadow file. (0 Replies)
Discussion started by: Perderabo
0 Replies
5. BSD
Hi,
I have a crappy hard disk and am trying to back up stuff from it onto my newer hopefully less crappy disk. There are dead sectors on the disk and some files can't be read (at all) so OpenBSD downgrades the transfer mode down until PIO mode 4. I noticed the transfer speed slowing down... (0 Replies)
Discussion started by: fiori_musicali
0 Replies
6. Solaris
Hi we work on solaris machines and access them in Command line mode using telnet services. Can they be accessed in GUI mode. If yes please advice as I have came to know that Solaris 9.0 supports GUI mode also. (1 Reply)
Discussion started by: sukhvinder_Tm
1 Replies
7. Red Hat
Hello everyone
Had a problem booting Fedora. I installed it as a server without any desktop environment(kde, gnome) except for X. Problem is when i booting system after it loads kernel suddenly screen messes up with parts of fedora graphics(it's not clear but you can see it -... (8 Replies)
Discussion started by: dimamu15
8 Replies
8. Hardware
Dear All,
i am trying to install the redhat linux using graphical mode...but it stucks while probing video card...i have installed linux using text mode it works fine and whole the installation goes fine. after installation if i give startx command it again stucks....looks like a vga card... (9 Replies)
Discussion started by: zaheer.gr8
9 Replies
9. Solaris
Hi Guys,
I have a sunblade 1500. I booted the system and it booted to maintenance mode. How can I fix this?
Thanks lots (8 Replies)
Discussion started by: cjashu
8 Replies
10. Fedora
Whenevr i am trying to access ROOT file in Fedora 15 by double clicking, its showing I dont have enough permission to access it and its not showing the inside access... How to solve it?? (4 Replies)
Discussion started by: amisubha
4 Replies
LEARN ABOUT FREEBSD
if_vmx
VMX(4) BSD Kernel Interfaces Manual VMX(4)
NAME
vmx -- VMware VMXNET3 Virtual Interface Controller device
SYNOPSIS
To compile this driver into the kernel, place the following line in your kernel configuration file:
device vmx
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_vmx_load="YES"
DESCRIPTION
The vmx driver provides support for the VMXNET3 virtual NIC available in virtual machines by VMware. It appears as a simple Ethernet device
but is actually a virtual network interface to the underlying host operating system.
This driver supports the VMXNET3 driver protocol, as an alternative to the emulated pcn(4), em(4) interfaces also available in the VMware
environment. The vmx driver is optimized for the virtual machine, it can provide advanced capabilities depending on the underlying host
operating system and the physical network interface controller of the host. The vmx driver supports features like multiqueue support, IPv6
checksum offloading, MSI/MSI-X support and hardware VLAN tagging in VMware's VLAN Guest Tagging (VGT) mode.
The vmx driver supports VMXNET3 VMware virtual NICs provided by the virtual machine hardware version 7 or newer, as provided by the following
products:
o VMware ESX/ESXi 4.0 and newer
o VMware Server 2.0 and newer
o VMware Workstation 6.5 and newer
o VMware Fusion 2.0 and newer
For more information on configuring this device, see ifconfig(8).
MULTIPLE QUEUES
The vmx driver supports multiple transmit and receive queues. Multiple queues are only supported by certain VMware products, such as ESXi.
The number of queues allocated depends on the presence of MSI-X, the number of configured CPUs, and the tunables listed below. FreeBSD does
not enable MSI-X support on VMware by default. The hw.pci.honor_msi_blacklist tunable must be disabled to enable MSI-X support.
LOADER TUNABLES
Tunables can be set at the loader(8) prompt before booting the kernel or stored in loader.conf(5).
hw.vmx.txnqueue
hw.vmx.X.txnqueue
Maximum number of transmit queues allocated by default by the driver. The default value is 8. The maximum supported by the VMXNET3
virtual NIC is 8.
hw.vmx.rxnqueue
hw.vmx.X.rxnqueue
Maximum number of receive queues allocated by default by the driver. The default value is 8. The maximum supported by the VMXNET3
virtual NIC is 16.
hw.vmx.txndesc
hw.vmx.X.txndesc
Number of transmit descriptors allocated by the driver. The default value is 512. The value must be a multiple of 32, and the maxi-
mum is 4096.
hw.vmx.rxndesc
hw.vmx.X.rxndesc
Number of receive descriptors per ring allocated by the driver. The default value is 256. The value must be a multiple of 32, and
the maximum is 2048. There are two rings so the actual usage is doubled.
EXAMPLES
The following entry must be added to the VMware configuration file to provide the vmx device:
ethernet0.virtualDev = "vmxnet3"
SEE ALSO
altq(4), arp(4), em(4), netintro(4), ng_ether(4), pcn(4), vlan(4), ifconfig(8)
AUTHORS
The vmx driver was ported from OpenBSD and significantly rewritten by Bryan Venteicher <bryanv@freebsd.org>. The OpenBSD driver was written
by Tsubai Masanari.
BSD
March 17, 2014 BSD