01-24-2014
Thank you,
I can i check the gatway because the ping and traceroute command don't specify the gateway
---------- Post updated at 03:41 PM ---------- Previous update was at 03:18 PM ----------
Do you know how its working the IBM "active dead gateway detection" ?
The format of the standard output ?
8 More Discussions You Might Find Interesting
1. High Performance Computing
Provides a description of how to set up a Solaris Cluster Express cluster in a VirtualBox on OpenSolaris.
More... (0 Replies)
Discussion started by: Linux Bot
0 Replies
2. High Performance Computing
Dear All,
Can anyone explain about Pros and Cons of SUN and Veritas Cluster ?
Any comparison chart is highly appreciated.
Regards,
RAA (4 Replies)
Discussion started by: RAA
4 Replies
3. Solaris
I folks,
season's greetings.
Hope you had a good festive season.
I've got 2 related problems on the same Sun Cluster 3.2.2 Apache 2.0.63 cluster:
clsetup error: ERROR: Failed to get connection to node localhost
SunOS... (0 Replies)
Discussion started by: cluster
0 Replies
4. Solaris
Yesterday my customer told me to expect a vcs upgrade to happen in the future. He also plans to stop using HDS and move to EMC.
Am thinking how to migrate to sun cluster setup instead.
My plan as follows leave the existing vcs intact as a fallback plan.
Then install and build suncluster on... (5 Replies)
Discussion started by: sparcguy
5 Replies
5. UNIX for Dummies Questions & Answers
hi power went out. next day unix sco wont boot up error code 303. any help appreciated as we are clueless. (11 Replies)
Discussion started by: fredthayer
11 Replies
6. Solaris
Hello experts -
I am planning to install a Sun cluster 4.0 zone cluster fail-over. few basic doubts.
(1) Where should i install the cluster s/w binaries ?. ( global zone or the container zone where i am planning to install the zone fail-over)
(2) Or should i perform the installation on... (0 Replies)
Discussion started by: NVA
0 Replies
7. Red Hat
Hi,
We are having many RedHat linux Server with Cluster facility for availability of service like HTTPD / MySQL.
We face some issue while some issue related to power disturbance / fluctuation or Network failure. There is two Cluster Node configured in... (0 Replies)
Discussion started by: hirenkmistry
0 Replies
8. Shell Programming and Scripting
Hi
I am using perl to ping a list of nodes - with script below :
$p = Net::Ping->new("icmp");
if ($p->ping($host,1)){
print "$host is alive.\n";
}
else {
print "$host is unreacheable.\n";
}
$p->close();... (4 Replies)
Discussion started by: tavanagh
4 Replies
LEARN ABOUT OPENDARWIN
traceroute6
TRACEROUTE6(8) BSD System Manager's Manual TRACEROUTE6(8)
NAME
traceroute6 -- print the route IPv6 packets will take to the destination
SYNOPSIS
traceroute6 [-dlnrv] [-f firsthop] [-g gateway] [-m hoplimit] [-p port] [-q probes] [-s src] [-w waittime] target [datalen]
DESCRIPTION
-d Debug mode.
-f firsthop
Specify how many hops to skip in trace.
-g gateway
Specify intermediate gateway (traceroute6 uses routing header).
-m hoplimit
Specify maximum hoplimit.
-l Print both host hostnames and numeric addresses. Normally traceroute6 prints only hostnames if -n is not specified, and only numeric
addresses if -n is specified.
-n Do not resolve numeric address to hostname.
-p port
Set UDP port number to port.
-q probes
Set the number of probe per hop count to probes.
-r
-s src Src specifies the source IPv6 address to be used.
-v Be verbose.
-w waittime
Specify the delay time between probes.
RETURN VALUES
The traceroute6 command will exit with 0 on success, and non-zero on errors.
SEE ALSO
ping(8), ping6(8), traceroute(8)
HISTORY
The traceroute6 command first appeared in WIDE hydrangea IPv6 protocol stack kit.
BSD
May 17, 1998 BSD