01-21-2014
Just going to follow up with what I did in hopes it helps someone else who has this issue arise.
Use diag command to check array and find failed disk(s).
# diag
---> Task Selection
---> RAID Array Manager
---> PCI-X SCSI Disk Array Manager
---> List PCI-X SCSI Disk Array Configuration
---> sisioa1 Available 06-08 PCI-X Dual Channel U320 SCSI RAID
Activate the LED indicator of the physical disk to locate it on the rack.
# diag
---> Task Selection
---> Hot Plug Task
---> SCSI and SCSI RAID Hot Plug Manager
---> Replace/Remove a Device Attached to an SCSI Hot Swap Enclosure
---> select failed disk here(pdisk#)
A message will appear in regards to an LED and Remove state. Find the physical drive that is now flashing amber from its LED and remove it from the array. After you remove the failed physical drive, replace it with the new unit.
Hit Enter on that message screen to remove that slot from the "remove state".
# diag
---> Task Selection
---> Hot Plug Task
---> SCSI and SCSI RAID Hot Plug Manager
---> Configure Added/Replaced Devices
# diag
---> Task Selection
---> Log Repair Action (Select affected disk)
Rebuild the array
# diag
---> Task Selection
---> RAID Array Manager
---> PCI-X SCSI Disk Array Manager
---> Reconstruct a PCI-X SCSI Disk Array
These 2 Users Gave Thanks to mpeter05 For This Post:
10 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
AIX 4.3.3
I am investigating methods of creating system backups. One method I am investigating is installing a hot swap hard drive and creating a mksysb to that hard drive. Does anyone have any ideas on getting this accomplished? I am thinking that I need a mounted file system from the 2nd... (0 Replies)
Discussion started by: jalburger
0 Replies
2. UNIX for Advanced & Expert Users
Hey everyone,
first of all, this is the motherboard I have: GigaByte GA-K8NXP-9 , nForce4 Ultra. It supports RAID 0, 1, 0+1 apparently both on the IDE and S-ATA HDD.
Now what I had in mind is popping 2 x 6Gb HDD in the IDE slots as slave 1 & 2 where my 2 DVD/CD burners are master. I then plan... (2 Replies)
Discussion started by: temba
2 Replies
3. UNIX for Dummies Questions & Answers
How do you view Drive/RAID configuration in UNIX?
We are running an ML370 with 6 drives in it...
Version: Sco 5.2.0
Sco Openserver Release 5 (2 Replies)
Discussion started by: bpoulson
2 Replies
4. OS X (Apple)
I am trying to recover data off a drive that failed in my iMac. Apple returned the drive to me and I purchased a hard drive enclosure. I have been doing research on prices for data recovery services, way too expensive. I seen some links using Unix DD commands in the terminal none of which worked.... (6 Replies)
Discussion started by: KJ1906
6 Replies
5. UNIX for Dummies Questions & Answers
Hello,
I have a machine that has software based RAID. One of the hard drives failed. The problem is that the old systems administrator created LVM and then RAID. My understanding is that RAID had to be created before and then the LVM's. Is there someway to install the new drive without loosing... (2 Replies)
Discussion started by: mojoman
2 Replies
6. Hardware
Hey All,
Im using Fedora 2.6 (which is cannot be changed for compatibility reasons).
I cloned a drive from a different server and when i added this drive to a new box, during startup it hangs on "Configuring Kernel Parameters:"
Is there any way to bypass this process and still boot... (0 Replies)
Discussion started by: robfwauk
0 Replies
7. Hardware
I am having trouble connecting my 4TB G-Raid Hard drive to my Compaq Hp laptop can anyone tell me how or what I need in order to connect the 4T and getting it working. (10 Replies)
Discussion started by: Jake Wolf
10 Replies
8. SCO
Our tape drive died and I installed a newer Quantum DAT72 drive in it's place with the same SCSI ID. It still works, but with one major flaw, the system will lock up if I try to upgrade BackupEDGE or view NFS settings in scoadmin.
I get a Transition to ready failure on ha=0* message when the... (4 Replies)
Discussion started by: psytropic
4 Replies
9. UNIX for Advanced & Expert Users
Good Evening,
2 years ago, I set up an Ubuntu file-server for a friend, who is a photograph amateur. Basically, the server offers a software RAID-5 that can be accessed remotely from a MAC. Unfortunately, I didn't labeled the hard drives (i.e. which physical drive corresponds to the /dev/sdX... (2 Replies)
Discussion started by: Loic Domaigne
2 Replies
10. Filesystems, Disks and Memory
I found out that the raid 1 was degraded:
# cat /proc/mdstat
Personalities :
md3 : active raid1 sda5 sdb5
1822445428 blocks super 1.0
md2 : active raid1 sda3(F) sdb3
1073741688 blocks super 1.0
md1 : active raid1 sda2 sdb2
524276 blocks super 1.0
md0 : active raid1 sda1... (0 Replies)
Discussion started by: ZaNaToS
0 Replies
ASR(4) BSD Kernel Interfaces Manual ASR(4)
NAME
asr -- driver for Adaptec I2O based SCSI/ATA host bus adapters
SYNOPSIS
device asr
DESCRIPTION
The Adaptec asr driver provides access to disks and disk arrays controlled by I2O based host bus adapters and SmartRAID SCSI RAID adapters
through the standard SCSI disk da(4) interface.
The supported adapters provide 64 bit PCI, Compact PCI, Zero Channel PCI, and up to four channels of Ultra2, Ultra 160, or Ultra320 SCSI, or
two channels of 1GB Fibre. All support RAID-0, RAID-1, RAID-10, RAID-5 and RAID-50 arrays. All SCSI target types are supported. For the
ATA based controllers, one IDE drive per channel is supported. Hot-swapping of IDE drives is not supported at this time.
All host bus adapters must be configured before they can be used with any operating system. Please contact Adaptec directly to obtain the
latest information on configuration utilities for the adapters. Currently there are both a Motif based GUI configuration utility and a CLI
based configuration utility available from the Adaptec Web site. The cards and arrays can also be configured via the BIOS based configura-
tion tool (SMOR).
HARDWARE
The adapters currently supported by the asr driver include the following:
o Adaptec Zero-Channel SCSI RAID 2000S, 2005S, 2010S, 2015S
o Adaptec SCSI RAID 2100S, 2110S
o Adaptec ATA-100 RAID 2400A
o Adaptec SCSI RAID 3200S, 3210S
o Adaptec SCSI RAID 3400S, 3410S
o Adaptec SmartRAID PM1554
o Adaptec SmartRAID PM1564
o Adaptec SmartRAID PM2554
o Adaptec SmartRAID PM2564
o Adaptec SmartRAID PM2664
o Adaptec SmartRAID PM2754
o Adaptec SmartRAID PM2865
o Adaptec SmartRAID PM3754
o Adaptec SmartRAID PM3755U2B / SmartRAID V Millennium
o Adaptec SmartRAID PM3757
o DEC KZPCC-AC (LVD 1-ch, 4MB or 16MB cache), DEC KZPCC-CE (LVD 3-ch, 64MB cache), DEC KZPCC-XC (LVD 1-ch, 16MB cache), DEC KZPCC-XE (LVD
3-ch, 64MB cache) -- rebadged SmartRAID V Millennium
FILES
/dev/asr* Adaptec SCSI RAID control nodes
NOTES
The ATA based controllers present their devices as SCSI-like devices via CAM. For IDE drives attached to these cards, a subset of standard
SCSI commands and mode pages are understood via translation performed in the card's firmware.
SEE ALSO
da(4)
HISTORY
The asr (Adaptec SCSI RAID) driver first appeared as the dpti2o driver under BSDi BSD/OS 3.2, then under FreeBSD 2.2.8 and was ported over to
the CAM layer represented in 4.0.
AUTHORS
The asr driver was kindly donated by Adaptec and is maintained by Mark Salyzyn <mark_salyzyn@adaptec.com>. This manual page was written by
Mark Salyzyn and fixed up by Jeroen Ruigrok van der Werven <asmodai@FreeBSD.org>.
BSD
July 14, 2004 BSD