01-17-2014
Hi Stuart,
Currently running SSSD on Centos and RHEL with GFS for authentication against AD without any issues, took a little time to setup. But there were no major gotcha's.
Regards
Gull04
7 More Discussions You Might Find Interesting
1. Windows & DOS: Issues & Discussions
Hi
Does anybody know the steps and requirements of the installation process of Windows Active Directory using Unix/Linux Bind DNS.
I will appreciate if somebody gives the answer. (1 Reply)
Discussion started by: Darwin Rodrigue
1 Replies
2. UNIX for Dummies Questions & Answers
Hello - I have a very vague question, which will probably result in vague answers because I don't have a lot of detailed information and I don't know a whole lot about active directory.
Our Windows/NT admin has been rolling out Active Directory over the past several weeks and as time goes on,... (1 Reply)
Discussion started by: rm -r *
1 Replies
3. UNIX for Dummies Questions & Answers
i would like to ask about unix with active directory..actually my situation is at ny place there already have dns server in unix based,i want to implement an active directory to the network..from what i read about active directory we have to used bind dns...some say that bind could not handle in... (1 Reply)
Discussion started by: nour
1 Replies
4. HP-UX
Hey,
I've asked questions about this project here before and gotten lots of help so I figured I'd give it another try.
I've recently set up my HP-UX environment to authenticate to a Windows Active Directory server (Windows Server 2003 R2).
I setup an account on Active Directory which works... (2 Replies)
Discussion started by: Rike255
2 Replies
5. Red Hat
Hi Friends,
I need your help to get some solution of one of my problem.
Ours is a mixed domain. Most of the servers are windows and very little linux servers. We are using the MS AD for authentication. My problem is, I want to authenticate linux servers against AD. I donot want to use any... (1 Reply)
Discussion started by: arumon
1 Replies
6. UNIX for Advanced & Expert Users
Is there anyone who is utilizing Active Directory (2008R2) for AIX user account management? If yes or if AD is possible with AIX systems, can you please share what to be done to get there?
Please advise. (1 Reply)
Discussion started by: Daniel Gate
1 Replies
7. UNIX for Beginners Questions & Answers
Hi,
How can we check users added through LDAP or AD. Users added through a group of AD or LDAP group. (2 Replies)
Discussion started by: Nishit
2 Replies
LEARN ABOUT DEBIAN
sss_debuglevel
SSS_DEBUGLEVEL(8) SSSD Manual pages SSS_DEBUGLEVEL(8)
NAME
sss_debuglevel - change debug level while SSSD is running
SYNOPSIS
sss_debuglevel [options] NEW_DEBUG_LEVEL
DESCRIPTION
sss_debuglevel changes debug level of SSSD monitor and providers to NEW_DEBUG_LEVEL while SSSD is running.
OPTIONS
-c,--config
Specify a non-default config file. The default is /etc/sssd/sssd.conf. For reference on the config file syntax and options, consult the
sssd.conf(5) manual page.
NEW_DEBUG_LEVEL
Bit mask that indicates which debug levels will be visible. 0x0010 is the default value as well as the lowest allowed value, 0xFFF0 is
the most verbose mode. This setting overrides the settings from config file.
Currently supported debug levels:
0x0010: Fatal failures. Anything that would prevent SSSD from starting up or causes it to cease running.
0x0020: Critical failures. An error that doesn't kill the SSSD, but one that indicates that at least one major feature is not going to
work properly.
0x0040: Serious failures. An error announcing that a particular request or operation has failed.
0x0080: Minor failures. These are the errors that would percolate down to cause the operation failure of 2.
0x0100: Configuration settings.
0x0200: Function data.
0x0400: Trace messages for operation functions.
0x1000: Trace messages for internal control functions.
0x2000: Contents of function-internal variables that may be interesting.
0x4000: Extremely low-level tracing information.
To log required debug levels, simply add their numbers together as shown in following examples:
Example: To log fatal failures, critical failures, serious failures and function data use 0x0270.
Example: To log fatal failures, configuration settings, function data, trace messages for internal control functions use 0x1310.
Note: This is new format of debug levels introduced in 1.7.0. Older format (numbers from 0-10) is compatible but deprecated.
AUTHORS
The SSSD upstream - http://fedorahosted.org/sssd
SSSD
03/04/2013 SSS_DEBUGLEVEL(8)