Specifically I'm getting : Reference Code 888 102 700 0C5 in HMC and AIX is hang as shown in the attached screenshot.
IBM Power7 reference codes for 888
I appreciate any tip or idea that might help
Hi guys
I have joined a new department and one of my tasks is to investigate the feasibility of upgrading our current AIX v 4.3 to V5.3.
I do not know anything about AIX and any actual work will be done by an outside consultant until such time as I have built up my own knowledge.
The system we... (3 Replies)
Hello everyone, I have to do a ML upgrade on AIX 5.2 from 01 to 09
this is the first time iam going to do it.
are there any command i have to keep in mind??
thanks! (1 Reply)
I have an IBM P520 that I need to upgrade from 5.2 to 5.3. My background in Unix is from 15 years ago so I don't remember much. IBM documentation is hard to find. Any help would be appreciated. (1 Reply)
I have an AIX LPAR that is one half of a Oracle RAC cluster running over a GPFS filesystem.
The OS version in the LPAR was 5300-05-01
I ran an upgrade to 5300-07-05 (Apply only, Commit=NO and preserve old files).
The preview passed with no failures detected.
The actual upgrade failed... (5 Replies)
Hello Folks,
i am facing some weired issues.
case is like this :-
initially i was on AIX 5.3
i have installed filesets related to my application and those were in APPLY state.(COMMIT is set as NO)
Then i have taken lslpp -l| grep -i <apps name>
in that i confirmed whether the filesets are... (1 Reply)
i upgrade aix ml 5.3.2.1 to 5.3.2.2 but when running commnd #oslevel -r
shows out put, again 5.3.2.1-- where should i chek???
2-can any one tell me when mknfs command run which files get updated?? (2 Replies)
Hi all,
i would like to know if it's possible upgrade AIX 5.3 to 6.1 on a LPAR without use the HMC.
so i would like to know if i must use the console to do it or i can do all from the up&running system on LPAR.
Thanks in advance.
Mario (4 Replies)
Dear Guys ..
I'm going to Upgrade one of the servers AIX 6.1
I want to stop rootvg mirror to save the mirror then upgrade to AIX 6.1 this is to help me in rollback if something goes wrong but ..
can anyone help me how to make sure that system is relay mirrored and how to know that second... (10 Replies)
Discussion started by: top.level
10 Replies
LEARN ABOUT NETBSD
ess
ESS(4) BSD Kernel Interfaces Manual ESS(4)NAME
ess -- ESS Technology AudioDrive family audio device driver
SYNOPSIS
ess* at isapnp?
ess* at pnpbios? index ?
ess* at ofisa?
audio* at audiobus?
opl* at ess?
DESCRIPTION
The ess driver provides support for the ESS 1788, 1888, 1887, and 888 AudioDrive audio devices.
The AudioDrive 1788 is a half-duplex device, while the 1888, 1887, and 888 are full-duplex. All are capable of 8- and 16-bit audio sample
recording and playback at rates up to 44.1kHz.
The AudioDrive takes 16 I/O ports. The I/O port range, IRQ, and DRQ channels are set by the driver to the values specified in the configura-
tion file (or for isapnp, pnpbios, or ofisa, the values assigned from the firmware). The I/O port base must be one of 0x220, 0x230, 0x240,
0x250. The IRQ must be one of 5, 7, 9, 10 (or 15 on the 1887 only). The first DRQ channel must be selected from 0, 1, 3. The second DRQ chan-
nel (used for playback by the full-duplex 1888/1887, ignored by the 1788) can additionally be set to 5. If both DRQ channels are used they
must be different.
The joystick interface (if enabled) is handled by the joy(4) driver.
SEE ALSO audio(4), isapnp(4), joy(4), ofisa(4), opl(4), pnpbios(4)HISTORY
The ess device driver appeared in NetBSD 1.4.
BUGS
The AudioDrive devices have a SoundBlaster compatibility mode, and may be detected by the SoundBlaster driver (see sb(4)) rather than the
AudioDrive driver. The workaround is to remove the SoundBlaster driver from the kernel configuration.
BSD June 22, 2005 BSD