Hi all,
I'm getting errors while booting AIX 7.1 after upgrade
I have used FLRT tool for the process with the following input values shown in the attached photo. titled FLRT
After reboot for the upgrade process system hangs and no response as shown in screenshot named AIX7.1-NormalBoot
I tried to boot in single user mode the system also hangs and gave me the below messages
Code:
-------------------------------------------------------------------------------
Welcome to AIX.
boot image timestamp: 13:47:15 12/26/2013
The current time and date: 19:13:09 12/26/2013
processor count: 1; memory size: 15552MB; kernel size: 35442232
boot device: /pci@80000002000000a/pci1014,0339@0/sas/disk@0
-------------------------------------------------------------------------------
DIAGNOSTIC OPERATING INSTRUCTIONS
LICENSED MATERIAL and LICENSED INTERNAL CODE - PROPERTY OF IBM.
(C) COPYRIGHTS BY IBM AND BY OTHERS 1982,1991-1995.
ALL RIGHTS RESERVED.
These programs allow you to enter diagnostics, service aids, single
user mode, or low-level maintenance mode. The diagnostics should be
used whenever problems with the system occur which have not been
corrected by any software application procedures available.
In general, the diagnostics will run automatically. However, sometimes
you will be required to select options, inform the system when to
continue, do simple tasks, and exchange diskettes.
Several keys are used to control the diagnostics:
- The Enter key continues the procedure or performs an action.
- The Backspace key allows keying errors to be corrected.
- The cursor keys are used to select an option.
To continue, press Enter.
FUNCTION SELECTION
1. Diagnostic Routines
This selection will test the machine hardware. Wrap plugs and
other advanced functions will not be used.
2. Advanced Diagnostic Routines
This selection will test the machine hardware. Wrap plugs and
other advanced functions will be used.
3. Task Selection(Diagnostics, Advanced Diagnostics, Service Aids, etc.)
This selection will list the tasks supported by these procedures.
Once a task is selected, a resource menu may be presented showing
all resources supported by the task.
4. Resource Selection
This selection will list the resources in the system that are supported
by the diagnostic programs. Once a resource is selected, a task menu will
be presented showing all tasks that can be run on the resource(s).
5. Single User Mode
The system will enter single-user mode for software maintenance.
To make a selection, type the number and press Enter [1]:5
The system will now continue the boot process. Please wait...exec(): 0509-036 Cannot load program ps because of the following errors:
0509-130 Symbol resolution failed for /usr/lib/libpthreads.a(shr_xpg5.o) because:
0509-136 Symbol thread_unlock_ (number 15) is not exported from
dependent module /unix.
0509-026 System error: Error 0
0509-192 Examine .loader section symbols with the
'dump -Tv' command.
Hi guys
I have joined a new department and one of my tasks is to investigate the feasibility of upgrading our current AIX v 4.3 to V5.3.
I do not know anything about AIX and any actual work will be done by an outside consultant until such time as I have built up my own knowledge.
The system we... (3 Replies)
Hello everyone, I have to do a ML upgrade on AIX 5.2 from 01 to 09
this is the first time iam going to do it.
are there any command i have to keep in mind??
thanks! (1 Reply)
I have an IBM P520 that I need to upgrade from 5.2 to 5.3. My background in Unix is from 15 years ago so I don't remember much. IBM documentation is hard to find. Any help would be appreciated. (1 Reply)
I have an AIX LPAR that is one half of a Oracle RAC cluster running over a GPFS filesystem.
The OS version in the LPAR was 5300-05-01
I ran an upgrade to 5300-07-05 (Apply only, Commit=NO and preserve old files).
The preview passed with no failures detected.
The actual upgrade failed... (5 Replies)
Hello Folks,
i am facing some weired issues.
case is like this :-
initially i was on AIX 5.3
i have installed filesets related to my application and those were in APPLY state.(COMMIT is set as NO)
Then i have taken lslpp -l| grep -i <apps name>
in that i confirmed whether the filesets are... (1 Reply)
i upgrade aix ml 5.3.2.1 to 5.3.2.2 but when running commnd #oslevel -r
shows out put, again 5.3.2.1-- where should i chek???
2-can any one tell me when mknfs command run which files get updated?? (2 Replies)
Hi all,
i would like to know if it's possible upgrade AIX 5.3 to 6.1 on a LPAR without use the HMC.
so i would like to know if i must use the console to do it or i can do all from the up&running system on LPAR.
Thanks in advance.
Mario (4 Replies)
Dear Guys ..
I'm going to Upgrade one of the servers AIX 6.1
I want to stop rootvg mirror to save the mirror then upgrade to AIX 6.1 this is to help me in rollback if something goes wrong but ..
can anyone help me how to make sure that system is relay mirrored and how to know that second... (10 Replies)