12-25-2013
Your question is not clear. Most servers have a single primary IP address. So, what does IPADDR2 refer to? A virtual (or zone)? An ISCSI SAN connection? We cannot guess and give decent answers.
Knowing the OS would help a lot.
10 More Discussions You Might Find Interesting
1. Solaris
Can someone please point me in the correct direction of where I configure the network information on SunOS 5.8 server? (Searching SunSolve and Google have resulted in thousands of fixes for potential errors, but I can't find the general instructions, etc. for starting the process).
Thanks! (2 Replies)
Discussion started by: FredSmith
2 Replies
2. Linux
Hello everybody,
How can link network interface to the output of lspci -vv. Basicly i need to know who is the manufacturer of a specific interface, for example eth0 {Is it an Intel, or Broadcome, or something else}. Is there a way to find that out?
Thanx (5 Replies)
Discussion started by: aleksey
5 Replies
3. AIX
hi all,
how do i change the routing info and make sure i will be able to connect remotely?
any ideas please?
thanks in advance. (1 Reply)
Discussion started by: itik
1 Replies
4. IP Networking
Hi,
how can i sftp or scp between 2 servers, when only i am able to ping to them.
they are on different network
10.130.170.31 -- server 1
10.130.230.141 -- server 2
i need to transfer data files from 1 to 2.
need your suggestions or help on these.
Regards
saha (4 Replies)
Discussion started by: saha
4 Replies
5. Shell Programming and Scripting
Hey guys,
I just started college a few days ago. To my dismay, my school has a very frustrating wireless network access system. Every time you want to use the network, you need to open up a browser and get re-directed to a login page. Every access, you need to reenter the same username and... (1 Reply)
Discussion started by: Chain Breaker
1 Replies
6. UNIX for Dummies Questions & Answers
Hello,
is there any tool where I can scan my netwrk and get all types of Unix servers? (2 Replies)
Discussion started by: fsmadi
2 Replies
7. UNIX and Linux Applications
In gnome there was an indicator applet that displayed your ip address, subnet mask, gateway, and dns. Is there a similar applet in kde? (0 Replies)
Discussion started by: cokedude
0 Replies
8. UNIX for Advanced & Expert Users
Is there a command that display all network info. I'm looking for ip address, subnet mask, gateway, and dns. If there isn't a single command could someone please write me a shellscript that can do this? (8 Replies)
Discussion started by: cokedude
8 Replies
9. UNIX for Advanced & Expert Users
Hi,
I'm trying to figure out how much traffic has been generated and received from netstat -s output (using Linux). I can see the output shows packet counts and Octet values, how would I correctly calculate how much traffic in and how much out?
My output below:
Ip:
88847576 total... (1 Reply)
Discussion started by: wilsonee
1 Replies
10. Shell Programming and Scripting
Hi,
I want to collect info from a no. of servers whether there grub.conf contain "elevator" parameter or not.
What I want is
sudo cat /etc/grub.conf | grep -q "elevator=noop"; echo $?
If output is "0", I want name of that host in a file called "present"
if its not "0", I want that... (4 Replies)
Discussion started by: stunn3r
4 Replies
LEARN ABOUT DEBIAN
nsd-xfer
nsd-xfer(8) nsd 3.2.12 nsd-xfer(8)
NAME
nsd-xfer - AXFR client to transfer zones from a name server
SYNOPSIS
nsd-xfer [-4] [-6] [-a address[@port]] [-p port] [-s serial] [-T tsiginfo] [-v] -z zone -f file servers
DESCRIPTION
Nsd-xfer is program to transfer zones from a name server using AXFR. NSD is a complete implementation of an authoritative DNS nameserver.
OPTIONS
-4 Only send to IPv4 addresses.
-6 Only send to IPv6 addresses.
-a address[@port]
Specify the source address (and port) to send from.
-f file
The file to store the zone in.
-p port
Specify the port to send to.
-s serial
Specify the serial of the current zone. The zone is only transferred if the master server has a zone with a greater serial number.
-T tsiginfo
Use TSIG to verify the zone transfer. The tsiginfo file must contain the TSIG key information. The file is removed upon successful
reading of the key. The format of the tsiginfo file is described in the doc/README file (section 3.3).
-v Be more verbose.
-z zone
Specify the zone to receive.
servers
List of nameservers to try.
EXAMPLES
To run this program the standard way type:
# nsd-xfer -z foobar.cz -f foobar.cz.zone 1.2.3.4
SEE ALSO
nsd(8), nsdc(8), nsd.conf(5), nsd-checkconf(8), nsd-notify(8), nsd-patch(8), zonec(8)
AUTHORS
NSD was written by NLnet Labs and RIPE NCC joint team. Please see CREDITS file in the distribution for further details.
NLnet Labs jul 19, 2012 nsd-xfer(8)