:mad: I have just recently got into using Linux RedHat 9. So far I love it, I have set it up on a server I am running. Right now I have set up Samba and am running a file server for my house. I have four computers, the linux box is connected to the internet through a switch I have. There are two... (5 Replies)
I have just recently got into using Linux RedHat 9. So far I love it, I have set it up on a server I am running. Right now I have set up Samba and am running a file server for my house. I have four computers, the linux box is connected to the internet through a switch I have. There are two NICS in... (1 Reply)
Hello All,
I know it's a tricky probably stupid question but I'm stuck.... :(
Is there any way to route different protocols through different eth cards for the same destination in Linux? With route add or something like it?
For instance:
FTP to/from 192.168.1.1 goes through eth0 - gw2... (1 Reply)
I am running a solaris 10 box and is just a workstation. I want to turn off the message below since it is annoying me.
Nov 15 12:16:07 stage5 in.routed: discard RIP response; source 134.56.105.2 not on interface eri0
This message only pops up when I am in a console. Telnet doesn't see it.
... (2 Replies)
nmap is a network utility which gives u information about open ports on ur system. for eg
$ nmap 10.226.112.202
PORT STATE SERVICE
7/tcp open echo
13/tcp open daytime
22/tcp open ssh
23/tcp open telnet
37/tcp open time
1100/tcp open unknown
these open... (2 Replies)
Hello. I want to Communicate 2 VLAN with router like this solution:
http://8pic.ir/images/83m0ouih8mmm9s1sfl56.jpg
For this purpose I'm configuring 2 Linux system as a switch and connect 4 host to them. Then a router is added to scenario.
The configuration of the switches is:
On DUT1(Linux):... (1 Reply)
Discussion started by: zsn
1 Replies
LEARN ABOUT NETBSD
rtquery
RTQUERY(8) BSD System Manager's Manual RTQUERY(8)NAME
rtquery -- query routing daemons for their routing tables
SYNOPSIS
rtquery [-1np] [-a secret] [-r addr] [-w timeout] host ...
rtquery [-t op] host ...
DESCRIPTION
rtquery is used to query a RIP network routing daemon, routed(8) or gated(8), for its routing table by sending a request or poll command.
The routing information in any routing response packets returned is displayed numerically and symbolically.
rtquery by default uses the request command. When the -p option is specified, rtquery uses the poll command, an undocumented extension to
the RIP protocol supported by gated(8). When querying gated(8), the poll command is preferred over the request command because the response
is not subject to Split Horizon and/or Poisoned Reverse, and because some versions of gated do not answer the request command. routed(8)
does not answer the poll command, but recognizes requests coming from rtquery and so answers completely.
rtquery is also used to turn tracing on or off in routed(8).
The following options are available:
-n displays only the numeric network and host numbers instead of both numeric and symbolic.
-p uses the poll command to request full routing information from gated(8). This is an undocumented extension RIP protocol supported
only by gated(8).
-1 queries using RIP version 1 instead of RIP version 2.
-w timeout
changes the delay for an answer from each host. By default, each host is given 15 seconds to respond.
-r addr
asks about the route to destination addr.
-a passwd=XXX
-a md5_passwd=XXX|KeyID
causes the query to be sent with the indicated cleartext or MD5 password.
-t op changes tracing, where op is one of the following. Requests from processes not running with UID 0 or on distant networks are gener-
ally ignored by the daemon except for a message in the system log. gated(8) is likely to ignore these debugging requests.
on=tracefile
turns tracing on into the specified file. That file must usually have been specified when the daemon was started or be the
same as a fixed name, often /etc/routed.trace.
more increases the debugging level.
off turns off tracing.
dump dumps the daemon's routing table to the current tracefile.
SEE ALSO gated(8), routed(8), pkgsrc/net/gated
Routing Information Protocol, RIPv1, RFC 1058, 1988.
Routing Information Protocol, RIPv2, RFC 1723, 1994.
BSD September 11, 2009 BSD