12-17-2013
I doubt it'd be part of the kernel.
this RHEL doc suggests quagga is what they use for it, though there's probably several options. Check what service is being used for it on the servers with lots of routes.
9 More Discussions You Might Find Interesting
1. Linux
How to use NAT Router in linux Redhat 6 ? and what
packages and configuration are required ? (1 Reply)
Discussion started by: salhoub
1 Replies
2. Red Hat
:mad: I have just recently got into using Linux RedHat 9. So far I love it, I have set it up on a server I am running. Right now I have set up Samba and am running a file server for my house. I have four computers, the linux box is connected to the internet through a switch I have. There are two... (5 Replies)
Discussion started by: xTHESEUSx
5 Replies
3. Red Hat
I have just recently got into using Linux RedHat 9. So far I love it, I have set it up on a server I am running. Right now I have set up Samba and am running a file server for my house. I have four computers, the linux box is connected to the internet through a switch I have. There are two NICS in... (1 Reply)
Discussion started by: xTHESEUSx
1 Replies
4. AIX
i have AIX Unix with "dynamic routing table" service enabled, but i do not need this service. How i can disable this service.
thanks (1 Reply)
Discussion started by: jdsnbr
1 Replies
5. Linux
how i add new routes to my linux machine (1 Reply)
Discussion started by: youmna
1 Replies
6. Linux
Hello All,
I know it's a tricky probably stupid question but I'm stuck.... :(
Is there any way to route different protocols through different eth cards for the same destination in Linux? With route add or something like it?
For instance:
FTP to/from 192.168.1.1 goes through eth0 - gw2... (1 Reply)
Discussion started by: pmpx
1 Replies
7. UNIX for Dummies Questions & Answers
I am running a solaris 10 box and is just a workstation. I want to turn off the message below since it is annoying me.
Nov 15 12:16:07 stage5 in.routed: discard RIP response; source 134.56.105.2 not on interface eri0
This message only pops up when I am in a console. Telnet doesn't see it.
... (2 Replies)
Discussion started by: tecky
2 Replies
8. Programming
nmap is a network utility which gives u information about open ports on ur system. for eg
$ nmap 10.226.112.202
PORT STATE SERVICE
7/tcp open echo
13/tcp open daytime
22/tcp open ssh
23/tcp open telnet
37/tcp open time
1100/tcp open unknown
these open... (2 Replies)
Discussion started by: anand121
2 Replies
9. IP Networking
Hello. I want to Communicate 2 VLAN with router like this solution:
http://8pic.ir/images/83m0ouih8mmm9s1sfl56.jpg
For this purpose I'm configuring 2 Linux system as a switch and connect 4 host to them. Then a router is added to scenario.
The configuration of the switches is:
On DUT1(Linux):... (1 Reply)
Discussion started by: zsn
1 Replies
LEARN ABOUT HPUX
ripquery
ripquery(1M) ripquery(1M)
NAME
ripquery - query RIP gateways
SYNOPSIS
authkey] dest[time] gateway ...
DESCRIPTION
is used to request all routes known by a RIP gateway by sending a RIP request or POLL command. The routing information in any routing pack-
ets returned is displayed numerically and symbolically. is intended to be used as a tool for debugging gateways, not for network manage-
ment. SNMP is the preferred protocol for network management.
by default uses the RIP POLL command, which is an undocumented extension to the RIP specification supported by on SunOS 3.x and later and
by 1.4 and later. The RIP POLL command is preferred over the RIP REQUEST command because it is not subject to Split Horizon and/or Poi-
soned Reverse. See the RIP RFC for more information.
Options
Send the query as a version 1 packet.
Send the query as a version 2 packet (default).
Specifies the authentication password to use for queries. If
specified, an authentication type of SIMPLE will be used, if is specified, an authentication type of MD5 will be used; oth-
erwise the default is an authentication type of NONE. Authentication fields in incoming packets will be displayed, but not
validated.
Prevents the address of the responding host from being looked up
to determine the symbolic name.
Specifies that the query should be for the specified
instead of complete routing table. The specification of the optional mask implies a version 2 query. Up to 23 requests about
specific destinations may be include in one packet.
Uses the RIP POLL command to request information from the routing
table. This is the default, but is an undocumented extension supported only by some versions of unOS 3.x and later versions
of If there is no response to the RIP POLL command, the RIP REQUEST command is tried. responds to a POLL command with all
the routes learned via RIP.
Used the RIP REQUEST command to request information from the
gateway's routing table. Unlike the RIP POLL command, all gateways should support the RIP REQUEST. If there is no response
to the RIP REQUEST command, the RIP POLL command is tried. responds to a REQUEST command with all the routes he announces
out the specified interface. Due to limitations in the UDP interface, on systems based on BSD 4.3 Reno or earlier, REQUESTs
respond about the interface used to route packets back to the sender. This can be avoided by running on the host being
queried.
Version information about
is displayed before querying the gateways.
Specifies the time in seconds to wait for the initial response
from a gateway. The default value is 5 seconds.
AUTHORS
Jeffrey C Honig.
SEE ALSO
gated(1M), gdc(1M), ospf_monitor(1M),
BUGS
Some versions of Unix do not allow looking up the symbolic name of a subnet.
ripquery(1M)