Linux - how to turn on the the RIP (dynamic routing) Post: 302880123

9 More Discussions You Might Find Interesting

1. Linux

NAT Routing in linux

How to use NAT Router in linux Redhat 6 ? and what packages and configuration are required ?

2. Red Hat

Setting Up Routing In Linux Redhat 9 Help

:mad: I have just recently got into using Linux RedHat 9. So far I love it, I have set it up on a server I am running. Right now I have set up Samba and am running a file server for my house. I have four computers, the linux box is connected to the internet through a switch I have. There are two...

3. Red Hat

Linux Routing Help

I have just recently got into using Linux RedHat 9. So far I love it, I have set it up on a server I am running. Right now I have set up Samba and am running a file server for my house. I have four computers, the linux box is connected to the internet through a switch I have. There are two NICS in...

4. AIX

Dynamic routing table

i have AIX Unix with "dynamic routing table" service enabled, but i do not need this service. How i can disable this service. thanks

5. Linux

linux routing

how i add new routes to my linux machine

6. Linux

Routing in Linux

Hello All, I know it's a tricky probably stupid question but I'm stuck.... :( Is there any way to route different protocols through different eth cards for the same destination in Linux? With route add or something like it? For instance: FTP to/from 192.168.1.1 goes through eth0 - gw2...

7. UNIX for Dummies Questions & Answers

How to turn off "discard RIP response" message

I am running a solaris 10 box and is just a workstation. I want to turn off the message below since it is annoying me. Nov 15 12:16:07 stage5 in.routed: discard RIP response; source 134.56.105.2 not on interface eri0 This message only pops up when I am in a console. Telnet doesn't see it. ...

8. Programming

c functions to turn off open ports in linux

nmap is a network utility which gives u information about open ports on ur system. for eg $ nmap 10.226.112.202 PORT STATE SERVICE 7/tcp open echo 13/tcp open daytime 22/tcp open ssh 23/tcp open telnet 37/tcp open time 1100/tcp open unknown these open...

9. IP Networking

Implement inter vlan routing with Linux

Hello. I want to Communicate 2 VLAN with router like this solution: http://8pic.ir/images/83m0ouih8mmm9s1sfl56.jpg For this purpose I'm configuring 2 Linux system as a switch and connect 4 host to them. Then a router is added to scenario. The configuration of the switches is: On DUT1(Linux):...

LEARN ABOUT LINUX

nrbroadcast

NRBROADCAST(5)						     Linux Programmer's Manual						    NRBROADCAST(5)

NAME

       nrbroadcast - NET/ROM routing broadcast configuration file.

DESCRIPTION

       Nrbroadcast  is	an ASCII file that contains information about each of the physical AX.25 ports that are to have NET/ROM routing broadcasts
       transmitted from them.

       Each line has the following format, each field being delimited by white space:

	      port minobs defqual worstqual verbose

       The field descriptions are:

	      port	    the port name of the AX.25 port to broadcast on.

	      minobs	    this is the minimum obsolescence count of a routing table entry to be broadcast on this port.

	      defqual	    this is the default quality of an incoming routing broadcast from an unknown neighbour.

	      worstqual     this is the worst quality node received from a routing broadcast that will be added to our routing table.

	      verbose	    whether the routes to all of my nodes in my routing table, or just the nodes resident on my machine are to	be  broad-
			    cast.

FILES

       /etc/ax25/nrbroadcast
       /etc/ax25/axports

SEE ALSO

       call(1), netrom(4), axports(5), netromd(8), nrparms(8).

Linux								   2 August 1996						    NRBROADCAST(5)