Sponsored Content
Special Forums IP Networking Similar systems - different communication speed Post 302880084 by rbatte1 on Tuesday 17th of December 2013 10:46:25 AM
Old 12-17-2013
Output from netstat -s would be good to see, even if it is a bit long.

Do you have a problem in FTP speed when you compare speeds just within company B?

We had a problem once where the auto-negotiation was wrong and we had a switch at 100M-Full duplex with a servers at 10M-Half. It all worked fine until we forced lots of data with an FTP, so it was difficult to track down.

You might need to ask the network manager to display the switch ports settings. You may be able to give IP address, or they may require the MAC address of your network card.


I regret I do not know how to display the requested and negotiated speeds on OSR. Can anyone else chip in?



Robin
 

8 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

serial communication

This isn't really a unix question, or even a programming question, but I hope you guys can help. I want to create a program to control the electricity on a model railway. I have created the program to that it sends characters over the serial cable, but now I need to do the switch that will... (1 Reply)
Discussion started by: KrazyGuyPaul
1 Replies

2. Filesystems, Disks and Memory

dmidecode, RAM speed = "Current Speed: Unknown"

Hello, I have a Supermicro server with a P4SCI mother board running Debian Sarge 3.1. This is the "dmidecode" output related to RAM info: RAM speed information is incomplete.. "Current Speed: Unknown", is there anyway/soft to get the speed of installed RAM modules? thanks!! Regards :)... (0 Replies)
Discussion started by: Santi
0 Replies

3. Solaris

help on network communication

Hi, Can anyone suggest a Unix command or c-shell algorithm to simulate to behavior of "wall" command minus the "all users"? What I'm trying to do is to send a notice to just one particular user but i dont want other remotely-logged-on users to receive the message (on the pseudo-terminals). I... (3 Replies)
Discussion started by: Deanne
3 Replies

4. HP-UX

Communication Failures

HI ALL, I have been trying to install a particular software using remote linux server. some thing like this: rsh <host ID> /usr/sbin/swinstall -x autoreboot=true -s /tmp/<software> <Product name>. The problem is whenever I try to install the product through a shell script the installation... (1 Reply)
Discussion started by: barun agarwal
1 Replies

5. Cybersecurity

Communication over firewall

Hey GUys, Once again I run in to problem and I am here for ur help. I have two sun(solaris) box on company LAN. One Unix Box is behind the firewall and the other one is Outside the firewall. The thing i need to do is remote display a graphic on Unix box outside the firewall to the Unixbox... (5 Replies)
Discussion started by: ajnabi
5 Replies

6. UNIX for Dummies Questions & Answers

Interprocess Communication

Hiya Everybody just joined, Not sure if this is the right section:o I require abit of an assistance with IPC! I know there are different types of IPC porcesses like signals, semaphores, mutexes, shared memory, message queues, pipes and sockets. Now say a system has a number of... (4 Replies)
Discussion started by: G.I.Joe
4 Replies

7. Filesystems, Disks and Memory

data from blktrace: read speed V.S. write speed

I analysed disk performance with blktrace and get some data: read: 8,3 4 2141 2.882115217 3342 Q R 195732187 + 32 8,3 4 2142 2.882116411 3342 G R 195732187 + 32 8,3 4 2144 2.882117647 3342 I R 195732187 + 32 8,3 4 2145 ... (1 Reply)
Discussion started by: W.C.C
1 Replies

8. What is on Your Mind?

From Systems Admin to Systems Eng.

I have been wondering how do Systems Administrators do the jump into Systems Engineering? Is it only a matter of time and experience or could I actually help myself get there? Opinions? Books I could read? Thanks a lot for your help! (0 Replies)
Discussion started by: svalenciatech
0 Replies
TXP(4)							   BSD Kernel Interfaces Manual 						    TXP(4)

NAME
txp -- 3Com 3XP Typhoon/Sidewinder (3CR990) Ethernet interface SYNOPSIS
To compile this driver into the kernel, place the following line in your kernel configuration file: device txp Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5): if_txp_load="YES" DESCRIPTION
The txp interface provides access to the 10Mb/s and 100Mb/s Ethernet networks via the 3Com Typhoon/Sidewinder chipset. Basic Ethernet functions are provided as well as support for vlan(4) tag removal and insertion assistance, receive ip(4), tcp(4), and udp(4) checksum offloading, and transmit ip(4) checksum offloading. There is currently no support for transmit tcp(4) or udp(4) checksum offload- ing, tcp(4) segmentation, nor ipsec(4) acceleration. Each of the host's network addresses is specified at boot time with an SIOCSIFADDR ioctl(2). The txp interface employs the address resolu- tion protocol described in arp(4) to dynamically map between Internet and Ethernet addresses on the local network. When a txp interface is brought up, by default, it will attempt to auto-negotiate the link speed and duplex mode. The speeds, in order of attempt, are: 100Mb/s Full Duplex, 100Mb/s Half Duplex, 10 Mb/s Full Duplex, and 10 Mb/s Half Duplex. The txp supports several media types, which are selected via the ifconfig(8) command. The supported media types are: media autoselect Attempt to autoselect the media type (default) media 100baseTX mediaopt full-duplex Use 100baseTX, full duplex media 100baseTX [mediaopt half-duplex] Use 100baseTX, half duplex media 10baseT mediaopt full-duplex Use 10baseT, full duplex media 10baseT [mediaopt half-duplex] Use 10baseT, half duplex HARDWARE
The txp driver supports the following cards: o 3Com 3CR990-TX-95 o 3Com 3CR990-TX-97 o 3Com 3cR990B-TXM o 3Com 3CR990SVR95 o 3Com 3CR990SVR97 o 3Com 3cR990B-SRV SEE ALSO
altq(4), arp(4), inet(4), intro(4), ip(4), miibus(4), tcp(4), udp(4), vlan(4), ifconfig(8) HISTORY
The txp driver first appeared in OpenBSD 2.9. BSD
March 12, 2009 BSD
All times are GMT -4. The time now is 02:41 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy