I want to write a script which would run from one host say A and connect to other remote host B and then run rest of commands in that host. I tried connecting from A host to B with SSH but after connecting to host B it just getting me inside Host B command prompt. Rest of the script is not running... (6 Replies)
Hi,
I wish to run a script located on a remote host machineB from machineA.
I am using ssh and running the below on machineA.
However, the ssh does not seem to work and freezes at
ssh -l wlsadmin machineB -v
Sun_SSH_1.1.2, SSH protocols 1.5/2.0, OpenSSL 0x0090704f
debug1: Reading... (9 Replies)
I am newbie in Unix and Expect script, so please help me :(
I'm using expect script for remote another host:
#!/usr/bin/expect -f
set timeout 10
spawn ssh -l root 10.120.18.4
expect "password:"
send "password\r"
expect "@"
interact
And now how can i use expect script for access mysql... (2 Replies)
OS~AIX 6.1
I'm running an interactive shell script i.e.,waits for a user response a few times while executing, after doing ssh to a AIX server. I'm just wondering what options I have if the ssh connection to the server is lost while executing the script, do I have to run the script again, which in... (2 Replies)
Hi All,
Noticed few posts around this but coudnt get exatcly what i wanted. Thanks for your help again.
I have a script running on a remote machine and i normally ssh from putty and run the script manually.
Is there anyway that i can write an HTML Code with a button so taht when I Click... (1 Reply)
Hi,
Given addresses of 2 remote machines, using a shell script is it possible to
get the state of running processes in "src"
stop all the processes in "src"
exit out of "src"
ssh into "dest"
resume the state of executing processes captured in step 1 in "dest"
Assumption:
"src" is... (3 Replies)
Geeks,
Could you please help me out in my script and identify the missing piece. I need to check/get the exit status of a remote command executed on remote host through script and send out an email when process/processes is/are not running on any/all server(s).
Here's the complete... (5 Replies)
Hi,
I got most of the script working, last part which does the ssh to remote and execute the command not working.
for SSH in ${HostList}; do
echo ${SSH}
echo ""
SSH2SEND=ssh user@${SSH} curl -v $URL
echo $SSH2SEND
done
error message I am getting ... (5 Replies)
I have below command to check for error logs from last 24 hours from the file : /var/log/messages/ The command is working fine on the local host.
sudo awk -F - -vDT="$(date --date="24 hours ago" "+%b %_d %H:%M:%S")" ' DT < $1' /var/log/messages | egrep -i "error|fail"
I want to run the... (8 Replies)
Discussion started by: rahul2662
8 Replies
LEARN ABOUT HPUX
dtsdate
dtsdate(1m)dtsdate(1m)NAME
dtsdate - Sets local clock from a remote dtsd server host
SYNOPSIS
dtsdate [-q] [-s] [-u] remote_host [nsecs]
ARGUMENTS
Queries the difference in time between the local host and the remote host, but does not change the local clock. The returned result (2 if
the time would have been reset, 1 if there was an error, and 0 otherwise) can be used by a script to determine what action to take. Causes
dtsdate to work silently, without showing the time. Shows the time in UTC, rather than in the current time zone. The name or the IP
address of a remote host that has a dtsd server. An integer giving the number of seconds by which the remote and local host times can dif-
fer, without the local host's clock being reset. If nsecs is 0, or if it is not specified, it is treated as if it were extremely large,
and no resetting occurs.
DESCRIPTION
The dtsdate command sets the local clock of a system to be the same as the host remote_host, running a dtsd server. The purpose of dtsdate
is to ensure that clock skew is minimized at initial cell configuration or at host instantiation, because it is difficult to start DCE and
its components if the skew is too great.
Clocks among all DCE components must be within five minutes of each other, to prevent failure of CDS and of security. Some DCE components
have even more stringent requirements. For instance, a DFS file server cannot start if its local host differs from other DFS hosts by more
than ten seconds.
The dtsdate command can be used for adjusting a clock backwards, before DCE is running on a host. Adjusting a clock backwards while DCE is
running can cause many difficulties, because security and file system software generally require system time to increase monotonically.
NOTES
The remote host must be running as a DTS server. This means that the dtsd on that system must have registered the DTS management inter-
face, because dtsdate uses the management call to get the current time from that host.
For dtsdate to be able to set the clock, it must run as a privileged user (root).
EXIT VALUE
If the -q argument is given, dtsdate returns 2 if the remote time and local time differ by more than nsecs, 1 if there was an error, and 0
otherwise.
If the -q argument is not given, dtsdate returns 1 if there was an error, and 0 otherwise.
EXAMPLES
With only the host argument:
dtsdate remotehost
dtsdate prints out the time on the remote host.
In this example:
dtsdate -s -q remotehost 10
dtsdate does not print out the remote host's time. If the times differ by more than 10 seconds, it returns the value of 1, otherwise 0.
In the next example:
dtsdate -s remotehost 10 dtsdate sets the clock if it differed from the remote clock by more than 10 seconds. It does this work
silently, because of the -s option.
The following example shows a shell script that uses the return value of dtsdate:
dtsdate -s -q remhost 10
result = $?
if [ $result -eq 0 ] ; then
echo "Time is within tolerence."
elif [ $result -eq 1 ] ; then
echo "Could not contact remote host." >&2
else # result = 2
if dtsdate remhost 10; then # it failed!
echo "Could not set the clock." >&2
fi
fi
RELATED INFORMATION
Commands: dtsd(1m)dtsdate(1m)