Sponsored Content
Special Forums IP Networking How to route all incoming packets from one virtual interface? Post 302879489 by neutronscott on Thursday 12th of December 2013 04:25:33 PM
Old 12-12-2013
I assume you're using Linux?

Quote:
Linux implements a weak host model: even if an address is configured on a given interface, this does not guarantee that packets generated on the host with that address as source will leave the host by that interface. Simply put, the destination IP address of the packet is used as the main key to select the best available route (gateway, interface) from the routing table.
You can make this happen using Linux Policy Routing. I've messed with this when I had two Internet connections and it can be a headache.

Here is a howto I found with Google that explains the steps I think you need: A Quick Introduction to Linux Policy Routing
This User Gave Thanks to neutronscott For This Post:
 

10 More Discussions You Might Find Interesting

1. Cybersecurity

~ IPTables : Limit Incoming UDP Packets With a Certain Length ~

Hello, I am currently trying to limit incoming UDP length 20 packets on a per IP basis to 5 a second using IPTables on a Linux machine (CentOS 5.2). Basically, if an IP is sending more than 5 length 20 UDP packet a second to the local machine, I would like the machine to drop the excess... (1 Reply)
Discussion started by: tomboy123
1 Replies

2. Solaris

Had to bounce interface to add network route

Hi All, yesterday I was trying to add a network route to my solaris 8 host using 'route add'. Everytime I tried, I kept getting the response 'network is unreachable'. I was trying all kinds of different methods, however I eventually got it to work after bouncing the interface that I was... (2 Replies)
Discussion started by: badoshi
2 Replies

3. Solaris

Route new network interface Solaris 8

Hi there, I'm trying to configure an additional network interface on Solaris 8 (eri0). The interface has been activated, but all the frames are still routed to the current default interface (ce0) I've tried following command (with various syntaxes...) unsuccessfully so far: # route add... (2 Replies)
Discussion started by: sreiniche
2 Replies

4. UNIX for Dummies Questions & Answers

Linux box drops the incoming packets

Hi all, I am new to Linux kernel. we have a c file that counts the no. of sends and received packets in each interface, and indicate the user about the error/drop ration of incoming and outgoing packets. in our Linux box , the incoming packets are dropped at random interval. we have our... (1 Reply)
Discussion started by: kannandv
1 Replies

5. Solaris

Network interface down after adding static route

Please , I have a problem I have add a statis route on Solaris 10, but after this, the network interface of Server was Offline. The system is in cluster mode (3.2) route add -net 10.10.1.128 -netmask 255.255.255.128 10.10.1.51 ------------------- lo0:... (1 Reply)
Discussion started by: Ruggero
1 Replies

6. Solaris

route and interface configuration in solaris

Hi, Every time when i boot my system i have to manually issue the following commands. ifconfig elxl0 plumb 192.168.200.129 netmask 255.255.255.0 up route add default 192.168.200.1 I need some help so that it should be configured permanently and i wouldn't have to manually issue... (2 Replies)
Discussion started by: malikshahid85
2 Replies

7. IP Networking

how to hack linux driver to delay incoming packets

hello, can anyone suggest how to delay the incoming packets ?? or how the packets are prossed inside the kernal and a way to make the packets wait a while?? it wud be vry helpful regards sameer (7 Replies)
Discussion started by: sameer kulkarni
7 Replies

8. Linux

how to allow incoming UDP packets with iptables

I am looking for an iptables command to allow incoming UDP packets for my Linux server also is there a command I can use to set the default action for outgoing packets to accept? Thank you (1 Reply)
Discussion started by: crimputt
1 Replies

9. IP Networking

Route packets over specified interface

Hi, I'm quite new to unix networking and ip tables. I'm running a debian (htpc) server with two NIC's; eth0 and wlan0. I'm trying to set it up in a way that eth0 is the default interface for internet, but some processes should run through wlan0. For example, I'm using eth0 for downloads... (2 Replies)
Discussion started by: Subbeh
2 Replies

10. IP Networking

How to route packets back to incoming interface?

Hi folks, I have a debian server running an Apache daemon on the eth0 interface. Now from time to time the server has to open an openvpn connection (tun0) to other networks to get some data from there. During this period the Apache is no longer reachable under it's IP address on eth0 because all... (6 Replies)
Discussion started by: flyingwalrus
6 Replies
SHOREWALL-PROXYARP(5)						  [FIXME: manual]					     SHOREWALL-PROXYARP(5)

NAME
proxyarp - Shorewall Proxy ARP file SYNOPSIS
/etc/shorewall/proxyarp DESCRIPTION
This file is used to define Proxy ARP. There is one entry in this file for each IP address to be proxied. The columns in the file are as follows. ADDRESS - address IP Address. INTERFACE - interface (Optional as of Shorewall 4.4.16) Local interface where system with the ip address in ADDRESS is connected. This column is only required when HAVEROUTE is set to No (no) or is left empty. EXTERNAL - interface External Interface to be used to access this system from the Internet. HAVEROUTE - [-|Yes|No] If there is already a route from the firewall to the host whose address is given, enter Yes or yes in this column. Otherwise, enter no or No or leave the column empty and Shorewall will add the route for you. If Shorewall adds the route, its persistence depends on the value of thePERSISTENT column contains Yes; otherwise, shorewall stop or shorewall clear will delete the route. PERSISTENT - [-|Yes|No] If HAVEROUTE is No or no, then the value of this column determines if the route added by Shorewall persists after a shorewall stop or a shorewall clear. If this column contains Yes or yes then the route persists; If the column is empty or contains No or no then the route is deleted by shorewall stop or shorewall clear. EXAMPLE
Example 1: Host with IP 155.186.235.6 is connected to interface eth1 and we want hosts attached via eth0 to be able to access it using that address. #ADDRESS INTERFACE EXTERNAL 155.186.235.6 eth1 eth0 FILES
/etc/shorewall/proxyarp SEE ALSO
http://shorewall.net/ProxyARP.htm http://shorewall.net/configuration_file_basics.htm#Pairs shorewall(8), shorewall-accounting(5), shorewall-actions(5), shorewall-blacklist(5), shorewall-hosts(5), shorewall_interfaces(5), shorewall-ipsets(5), shorewall-maclist(5), shorewall-masq(5), shorewall-nat(5), shorewall-netmap(5), shorewall-params(5), shorewall-policy(5), shorewall-providers(5), shorewall-rtrules(5), shorewall-routestopped(5), shorewall-rules(5), shorewall.conf(5), shorewall-secmarks(5), shorewall-tcclasses(5), shorewall-tcdevices(5), shorewall-tcrules(5), shorewall-tos(5), shorewall-tunnels(5), shorewall-zones(5) [FIXME: source] 06/28/2012 SHOREWALL-PROXYARP(5)
All times are GMT -4. The time now is 08:21 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy