Sponsored Content
Special Forums IP Networking How to route all incoming packets from one virtual interface? Post 302879445 by faka on Thursday 12th of December 2013 01:13:54 PM
Old 12-12-2013
How to route all incoming packets from one virtual interface?

Hello, I'm trying to route all packets arriving at a particular interface by entering the same interface
the virtual interface eth1: 2 and now everything is routed by default gw configured on eth1.
Code:
eth1      Link encap:Ethernet  HWaddr 0a:0e:64:18:52:72
          inet addr:192.168.10.15
eth1:2    Link encap:Ethernet  HWaddr 0a:0e:64:18:52:72
          inet addr:192.168.10.23

default gw
Code:
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
192.168.10.0    *               255.255.255.0   U     0      0        0 eth1
default         192.168.10.254  0.0.0.0         UG    0      0        0 eth1

I want all incoming packets from 192.168.10.23 going out from the same interface.

Some help?

Last edited by Franklin52; 12-13-2013 at 05:12 AM.. Reason: Please use code tags
 

10 More Discussions You Might Find Interesting

1. Cybersecurity

~ IPTables : Limit Incoming UDP Packets With a Certain Length ~

Hello, I am currently trying to limit incoming UDP length 20 packets on a per IP basis to 5 a second using IPTables on a Linux machine (CentOS 5.2). Basically, if an IP is sending more than 5 length 20 UDP packet a second to the local machine, I would like the machine to drop the excess... (1 Reply)
Discussion started by: tomboy123
1 Replies

2. Solaris

Had to bounce interface to add network route

Hi All, yesterday I was trying to add a network route to my solaris 8 host using 'route add'. Everytime I tried, I kept getting the response 'network is unreachable'. I was trying all kinds of different methods, however I eventually got it to work after bouncing the interface that I was... (2 Replies)
Discussion started by: badoshi
2 Replies

3. Solaris

Route new network interface Solaris 8

Hi there, I'm trying to configure an additional network interface on Solaris 8 (eri0). The interface has been activated, but all the frames are still routed to the current default interface (ce0) I've tried following command (with various syntaxes...) unsuccessfully so far: # route add... (2 Replies)
Discussion started by: sreiniche
2 Replies

4. UNIX for Dummies Questions & Answers

Linux box drops the incoming packets

Hi all, I am new to Linux kernel. we have a c file that counts the no. of sends and received packets in each interface, and indicate the user about the error/drop ration of incoming and outgoing packets. in our Linux box , the incoming packets are dropped at random interval. we have our... (1 Reply)
Discussion started by: kannandv
1 Replies

5. Solaris

Network interface down after adding static route

Please , I have a problem I have add a statis route on Solaris 10, but after this, the network interface of Server was Offline. The system is in cluster mode (3.2) route add -net 10.10.1.128 -netmask 255.255.255.128 10.10.1.51 ------------------- lo0:... (1 Reply)
Discussion started by: Ruggero
1 Replies

6. Solaris

route and interface configuration in solaris

Hi, Every time when i boot my system i have to manually issue the following commands. ifconfig elxl0 plumb 192.168.200.129 netmask 255.255.255.0 up route add default 192.168.200.1 I need some help so that it should be configured permanently and i wouldn't have to manually issue... (2 Replies)
Discussion started by: malikshahid85
2 Replies

7. IP Networking

how to hack linux driver to delay incoming packets

hello, can anyone suggest how to delay the incoming packets ?? or how the packets are prossed inside the kernal and a way to make the packets wait a while?? it wud be vry helpful regards sameer (7 Replies)
Discussion started by: sameer kulkarni
7 Replies

8. Linux

how to allow incoming UDP packets with iptables

I am looking for an iptables command to allow incoming UDP packets for my Linux server also is there a command I can use to set the default action for outgoing packets to accept? Thank you (1 Reply)
Discussion started by: crimputt
1 Replies

9. IP Networking

Route packets over specified interface

Hi, I'm quite new to unix networking and ip tables. I'm running a debian (htpc) server with two NIC's; eth0 and wlan0. I'm trying to set it up in a way that eth0 is the default interface for internet, but some processes should run through wlan0. For example, I'm using eth0 for downloads... (2 Replies)
Discussion started by: Subbeh
2 Replies

10. IP Networking

How to route packets back to incoming interface?

Hi folks, I have a debian server running an Apache daemon on the eth0 interface. Now from time to time the server has to open an openvpn connection (tun0) to other networks to get some data from there. During this period the Apache is no longer reachable under it's IP address on eth0 because all... (6 Replies)
Discussion started by: flyingwalrus
6 Replies
Match-all classifier in tc(8)                                          Linux                                         Match-all classifier in tc(8)

NAME
matchall - traffic control filter that matches every packet SYNOPSIS
tc filter ... matchall [ skip_sw | skip_hw ] [ action ACTION_SPEC ] [ classid CLASSID ] DESCRIPTION
The matchall filter allows to classify every packet that flows on the port and run a action on it. OPTIONS
action ACTION_SPEC Apply an action from the generic actions framework on matching packets. classid CLASSID Push matching packets into the class identified by CLASSID. skip_sw Do not process filter by software. If hardware has no offload support for this filter, or TC offload is not enabled for the inter- face, operation will fail. skip_hw Do not process filter by hardware. EXAMPLES
To create ingress mirroring from port eth1 to port eth2: tc qdisc add dev eth1 handle ffff: ingress tc filter add dev eth1 parent ffff: matchall skip_sw action mirred egress mirror dev eth2 The first command creats an ingress qdisc with handle ffff: on device eth1 where the second command attaches a matchall filters on it that mirrors the packets to device eth2. To create egress mirroring from port eth1 to port eth2: tc qdisc add dev eth1 handle 1: root prio tc filter add dev eth1 parent 1: matchall skip_sw action mirred egress mirror dev eth2 The first command creats an egress qdisc with handle 1: that replaces the root qdisc on device eth1 where the second command attaches a matchall filters on it that mirrors the packets to device eth2. To sample one of every 100 packets flowing into interface eth0 to psample group 12: tc qdisc add dev eth0 handle ffff: ingress tc filter add dev eth0 parent ffff: matchall action sample rate 100 group 12 SEE ALSO
tc(8), iproute2 21 Oct 2015 Match-all classifier in tc(8)
All times are GMT -4. The time now is 01:04 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy