How to route all incoming packets from one virtual interface?
Hello, I'm trying to route all packets arriving at a particular interface by entering the same interface
the virtual interface eth1: 2 and now everything is routed by default gw configured on eth1.
default gw
I want all incoming packets from 192.168.10.23 going out from the same interface.
Some help?
Last edited by Franklin52; 12-13-2013 at 05:12 AM..
Reason: Please use code tags
Hello,
I am currently trying to limit incoming UDP length 20 packets on a per IP basis to 5 a second using IPTables on a Linux machine (CentOS 5.2).
Basically, if an IP is sending more than 5 length 20 UDP packet a second to the local machine, I would like the machine to drop the excess... (1 Reply)
Hi All,
yesterday I was trying to add a network route to my solaris 8 host using 'route add'. Everytime I tried, I kept getting the response 'network is unreachable'.
I was trying all kinds of different methods, however I eventually got it to work after bouncing the interface that I was... (2 Replies)
Hi there,
I'm trying to configure an additional network interface on Solaris 8 (eri0). The interface has been activated, but all the frames are still routed to the current default interface (ce0) I've tried following command (with various syntaxes...) unsuccessfully so far:
# route add... (2 Replies)
Hi all,
I am new to Linux kernel.
we have a c file that counts the no. of sends and received packets in each interface, and indicate the user about the error/drop ration of incoming and outgoing packets.
in our Linux box , the incoming packets are dropped at random interval.
we have our... (1 Reply)
Please , I have a problem
I have add a statis route on Solaris 10, but after this, the network interface of Server was Offline.
The system is in cluster mode (3.2)
route add -net 10.10.1.128 -netmask 255.255.255.128 10.10.1.51
-------------------
lo0:... (1 Reply)
Hi,
Every time when i boot my system i have to manually issue the following commands.
ifconfig elxl0 plumb 192.168.200.129 netmask 255.255.255.0 up
route add default 192.168.200.1
I need some help so that it should be configured permanently and i wouldn't have to manually issue... (2 Replies)
hello,
can anyone suggest how to delay the incoming packets ??
or how the packets are prossed inside the kernal and a way to make the packets wait a while??
it wud be vry helpful
regards
sameer (7 Replies)
I am looking for an iptables command to allow incoming UDP packets for my Linux server
also is there a command I can use to set the default action for outgoing packets to accept?
Thank you (1 Reply)
Hi,
I'm quite new to unix networking and ip tables. I'm running a debian (htpc) server with two NIC's; eth0 and wlan0.
I'm trying to set it up in a way that eth0 is the default interface for internet, but some processes should run through wlan0.
For example, I'm using eth0 for downloads... (2 Replies)
Hi folks,
I have a debian server running an Apache daemon on the eth0 interface. Now from time to time the server has to open an openvpn connection (tun0) to other networks to get some data from there. During this period the Apache is no longer reachable under it's IP address on eth0 because all... (6 Replies)
Discussion started by: flyingwalrus
6 Replies
LEARN ABOUT DEBIAN
vlan-interfaces
VLAN-INTERFACES(5) File formats VLAN-INTERFACES(5)NAME
/etc/network/interfaces (vlan) - vlan extensions for the interfaces(5) file format
DESCRIPTION
/etc/network/interfaces contains network interface configuration information for the ifup(8) and ifdown(8) commands. This manpage
describes the vlan extensions to the standard interfaces(5) file format.
Primary extensions exist to make and destroy vlan interfaces, secondary extensions exist for ipv4 interface manipulation which are gener-
ally needed when using (a lot of) vlans.
VLAN CREATION
Vlan interface definitions exist of the vlan interface name, and an optional 'raw-device' parameter. Vlan interfaces are numbered 1 to
4095. You have the option to have interface names zero-padded to 4 numbers, or just the plain digits without leading zero. The following
example shows four ways to create a vlan with id 1 on interface eth0. They all result in different names.
iface eth0.1 inet static
address 192.168.1.1
netmask 255.255.255.0
iface vlan1 inet static
vlan-raw-device eth0
address 192.168.1.1
netmask 255.255.255.0
iface eth0.0001 inet static
address 192.168.1.1
netmask 255.255.255.0
iface vlan0001 inet static
vlan-raw-device eth0
address 192.168.1.1
netmask 255.255.255.0
# We don't have br support out of the box
iface br0.2 inet static
vlan-raw-device br0
address 192.168.1.1
netmask 255.255.255.0
# Aliases are ignored
iface br0.2:1 inet static
address 192.168.1.1
netmask 255.255.255.255
EXTRA IFACE OPTIONS
Usually someone who uses vlans also wants to do some other manipulations with the ip stack or interface.
vlan-raw-device devicename
Indicates the device to create the vlan on. This is ignored when the devicename is part of the vlan interface name.
ip-proxy-arp 0|1
Turn proxy-arp off or on for this specific interface. This also works on plain ethernet like devices.
ip-rp-filter 0|1|2
Set the return path filter for this specific interface. This also works on plain ethernet like devices.
hw-mac-address mac-address
This sets the mac address of the interface before bringing it up. This works on any device that allows setting the hardware address
with the ip command.
AUTHOR
This manpage was adapted from interfaces(5) by Ard van Breemen <ard@kwaak.net>
SEE ALSO vconfig(8)interfaces(5)vlan September 30 2007 VLAN-INTERFACES(5)