Sponsored Content
Special Forums IP Networking How to route all incoming packets from one virtual interface? Post 302879445 by faka on Thursday 12th of December 2013 01:13:54 PM
Old 12-12-2013
How to route all incoming packets from one virtual interface?

Hello, I'm trying to route all packets arriving at a particular interface by entering the same interface
the virtual interface eth1: 2 and now everything is routed by default gw configured on eth1.
Code:
eth1      Link encap:Ethernet  HWaddr 0a:0e:64:18:52:72
          inet addr:192.168.10.15
eth1:2    Link encap:Ethernet  HWaddr 0a:0e:64:18:52:72
          inet addr:192.168.10.23

default gw
Code:
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
192.168.10.0    *               255.255.255.0   U     0      0        0 eth1
default         192.168.10.254  0.0.0.0         UG    0      0        0 eth1

I want all incoming packets from 192.168.10.23 going out from the same interface.

Some help?

Last edited by Franklin52; 12-13-2013 at 05:12 AM.. Reason: Please use code tags
 

10 More Discussions You Might Find Interesting

1. Cybersecurity

~ IPTables : Limit Incoming UDP Packets With a Certain Length ~

Hello, I am currently trying to limit incoming UDP length 20 packets on a per IP basis to 5 a second using IPTables on a Linux machine (CentOS 5.2). Basically, if an IP is sending more than 5 length 20 UDP packet a second to the local machine, I would like the machine to drop the excess... (1 Reply)
Discussion started by: tomboy123
1 Replies

2. Solaris

Had to bounce interface to add network route

Hi All, yesterday I was trying to add a network route to my solaris 8 host using 'route add'. Everytime I tried, I kept getting the response 'network is unreachable'. I was trying all kinds of different methods, however I eventually got it to work after bouncing the interface that I was... (2 Replies)
Discussion started by: badoshi
2 Replies

3. Solaris

Route new network interface Solaris 8

Hi there, I'm trying to configure an additional network interface on Solaris 8 (eri0). The interface has been activated, but all the frames are still routed to the current default interface (ce0) I've tried following command (with various syntaxes...) unsuccessfully so far: # route add... (2 Replies)
Discussion started by: sreiniche
2 Replies

4. UNIX for Dummies Questions & Answers

Linux box drops the incoming packets

Hi all, I am new to Linux kernel. we have a c file that counts the no. of sends and received packets in each interface, and indicate the user about the error/drop ration of incoming and outgoing packets. in our Linux box , the incoming packets are dropped at random interval. we have our... (1 Reply)
Discussion started by: kannandv
1 Replies

5. Solaris

Network interface down after adding static route

Please , I have a problem I have add a statis route on Solaris 10, but after this, the network interface of Server was Offline. The system is in cluster mode (3.2) route add -net 10.10.1.128 -netmask 255.255.255.128 10.10.1.51 ------------------- lo0:... (1 Reply)
Discussion started by: Ruggero
1 Replies

6. Solaris

route and interface configuration in solaris

Hi, Every time when i boot my system i have to manually issue the following commands. ifconfig elxl0 plumb 192.168.200.129 netmask 255.255.255.0 up route add default 192.168.200.1 I need some help so that it should be configured permanently and i wouldn't have to manually issue... (2 Replies)
Discussion started by: malikshahid85
2 Replies

7. IP Networking

how to hack linux driver to delay incoming packets

hello, can anyone suggest how to delay the incoming packets ?? or how the packets are prossed inside the kernal and a way to make the packets wait a while?? it wud be vry helpful regards sameer (7 Replies)
Discussion started by: sameer kulkarni
7 Replies

8. Linux

how to allow incoming UDP packets with iptables

I am looking for an iptables command to allow incoming UDP packets for my Linux server also is there a command I can use to set the default action for outgoing packets to accept? Thank you (1 Reply)
Discussion started by: crimputt
1 Replies

9. IP Networking

Route packets over specified interface

Hi, I'm quite new to unix networking and ip tables. I'm running a debian (htpc) server with two NIC's; eth0 and wlan0. I'm trying to set it up in a way that eth0 is the default interface for internet, but some processes should run through wlan0. For example, I'm using eth0 for downloads... (2 Replies)
Discussion started by: Subbeh
2 Replies

10. IP Networking

How to route packets back to incoming interface?

Hi folks, I have a debian server running an Apache daemon on the eth0 interface. Now from time to time the server has to open an openvpn connection (tun0) to other networks to get some data from there. During this period the Apache is no longer reachable under it's IP address on eth0 because all... (6 Replies)
Discussion started by: flyingwalrus
6 Replies
VDE_L3(1)						      General Commands Manual							 VDE_L3(1)

NAME
vde_l3 - Virtual Distributed Ethernet 'Layer 3' Switch. SYNOPSIS
vde_l3 -v vde_plug:ipaddress/netmask [-v...] [-r target_network/netmask:gateway] [-G default_gw] [-M mgmt_socket] DESCRIPTION
A vde_l3 connects to one or more vde_switches, performing ip forwarding among its virtual interfaces. A new interface is created at startup for each -v option given at command line. Static routes to target networks can be defined using the -r option. vde_l3 -v /var/run/s1.ctl:192.168.0.1/24 connects to the vde sock at /var/run/s1.ctl with its virtual interface ve0, having the address 192.168.0.1 and netmask 255.255.255.0. vde_l3 -v /var/run/s1.ctl:192.168.0.1/24 -v /var/run/s2.ctl:10.0.0.254/255.255.0.0 connects to the two vde socks, with its virtual interfaces ve0 and ve1, having addressess 192.168.1.0 and 10.0.0.254 respectively. Hosts in each network can specify the vde_l3 as their gateway to reach the other one. OPTIONS
-v vde_plug:ipaddress/netmask Creates a virtual network interfaces on the vde_l3 box, with address ipaddress and netmask netmask. Please note that the netmask can be specified either in the 'classic' A.B.C.D mode, or just by giving the number of leading bits (f.e., /17 for 255.255.128.0). One can define as many interfaces as she wants. -r target_network/netmask:gateway Specify a static route through gateway to reach hosts in target_network with netmask netmask. One can define as many routes as she wants. -G default_gw Specify a default gateway, to be used whenever no static route is defined for a target host. -M mgmt_socket the unix socket where the parameters (interfaces addresses, routes, etc.) can be checked and changed runtime. unixterm(1) can be used as a remote terminal for wirefilter. NOTICE
Virtual Distributed Ethernet is not related in any way with www.vde.com ("Verband der Elektrotechnik, Elektronik und Informationstechnik" i.e. the German "Association for Electrical, Electronic & Information Technologies"). SEE ALSO
vde_switch(1), vdeq(1), unixterm(1), vde_cryptcab(1), wirefilter(1). AUTHORS
VDE_L3 is a tool by Daniele Lacamera <root@danielinux.net> VDE is a project by Renzo Davoli <renzo@cs.unibo.it> Virtual Distributed Ethernet May 7, 2007 VDE_L3(1)
All times are GMT -4. The time now is 08:12 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy