12-12-2013
POST REMOVED
Reason: Relative to Solaris 10 only.
Last edited by hicksd8; 12-13-2013 at 06:18 AM..
10 More Discussions You Might Find Interesting
1. Solaris
I am seeking help from the gurus in this forum and hope that I can find answers soon. Anyone who provide the answers will be greatly appreciated.
I have a sparc box with Solaris 10 on it. We install Solaris with zone structure. One global zone and two other zone. I installed Oracle DB on global... (6 Replies)
Discussion started by: duke0001
6 Replies
2. Solaris
Hi Everyone,
I have installed open solaris 10 on one of the x86 machines available but inspite of configuring the IP i am unable to access the machine through the network.
Can anyone please help me wih the settings required to access the machine across the network.Its really Urg..Any help is... (13 Replies)
Discussion started by: sankasu
13 Replies
3. Solaris
Hi
i have created a solaris zone but have not yet connected any network cables for this new zone,
can i set the zone up without running the command 'add net' and not adding an ip or physical interface?
i tried to add dummy internet settings and get this
zonecfg:coddr> add net... (4 Replies)
Discussion started by: newbiesolaris10
4 Replies
4. Solaris
I am trying to use a serial communications device that is connected to /dev/ttyb on a netra 240 server. This is a solaris zone configuration using solaris 10 0910. I am able to access /dev/ttyb from the global zone but not throught he non-global zone. I have enabled all of the tty devices in my... (0 Replies)
Discussion started by: disagreeable
0 Replies
5. Solaris
I am trying to create a branded 10 zone on a Solaris 11.1 control domain. I am using a flar image (cpio) from an existing LDOM. Here are the steps taken after flarcreate.
#zonecfg -z <device>
>create -b
>set brand=solaris10
>set zonepath=/zonez/<device>
>set ip-type=exclusive
>add net... (1 Reply)
Discussion started by: aeroforce
1 Replies
6. UNIX for Advanced & Expert Users
Dear all,
recently, I migrated a solaris zone from one host to another. The zone was inside of a zpool. The zpool cotains two volumes.
I did the following:
host1:
$ zlogin zone1 shutdown -y -g0 -i0 #Zone status changes from running to installed
$ zpool export zone1
host2:
$ zpool... (2 Replies)
Discussion started by: custos
2 Replies
7. Solaris
Have 2 nics on physical system
net0 phys 1500 up --
net1 phys 1500 up --
1. I want to create a link aggregation with LACP enabled with above 2 nics
2. Create port-group(Like we create on ESXi) with VLAN-ID 2141
3. And assign this... (0 Replies)
Discussion started by: Shirishlnx
0 Replies
8. Solaris
I am planning to do solaris 11 global zone patching having solaris 10 branded zone. I have a doubts on step 8 specially
Can someone clear my step 8 doubts or if anything wrong between step 1 to step 9 please correct that also as I have pretty good idea about Step 10 mean patching in solaris 10... (2 Replies)
Discussion started by: amity
2 Replies
9. Solaris
Hi,
I have a Solaris 10 zone which I need to configure on a new network. I have configured the new IP on the zone itself and I can ping the interface from a node on the same network, but not from another network. Basically I need to know how to route the traffic from the zone to it's... (3 Replies)
Discussion started by: sparcman
3 Replies
10. Solaris
Hi, hoping someone can help, its been a while since I used Solaris.
After creating a NGZ (non global zone), the NGZ can access the GZ (Global Zone) and the GZ can access the NGZ (using ssh, zlogin)
However, the NGZ cannot access any other netwqork devices, it can't even see the default router
... (2 Replies)
Discussion started by: GazinLincoln
2 Replies
LEARN ABOUT LINUX
net_adm
net_adm(3erl) Erlang Module Definition net_adm(3erl)
NAME
net_adm - Various Erlang Net Administration Routines
DESCRIPTION
This module contains various network utility functions.
EXPORTS
dns_hostname(Host) -> {ok, Name} | {error, Host}
Types Host = atom() | string()
Name = string()
Returns the official name of Host , or {error, Host} if no such name is found. See also inet(3erl) .
host_file() -> Hosts | {error, Reason}
Types Hosts = [Host]
Host = atom()
Reason = term()
Reads the .hosts.erlang file, see the section Files below. Returns the hosts in this file as a list, or returns {error, Reason} if
the file could not be read. See file(3erl) for possible values of Reason .
localhost() -> Name
Types Name = string()
Returns the name of the local host. If Erlang was started with the -name command line flag, Name is the fully qualified name.
names() -> {ok, [{Name, Port}]} | {error, Reason}
names(Host) -> {ok, [{Name, Port}]} | {error, Reason}
Types Name = string()
Port = int()
Reason = address | term()
Similar to epmd -names , see epmd(1) . Host defaults to the local host. Returns the names and associated port numbers of the Erlang
nodes that epmd at the specified host has registered.
Returns {error, address} if epmd is not running. See inet(3erl) for other possible values of Reason .
(arne@dunn)1> net_adm:names().
{ok,[{"arne",40262}]}
ping(Node) -> pong | pang
Types Node = node()
Tries to set up a connection to Node . Returns pang if it fails, or pong if it is successful.
world() -> [node()]
world(Arg) -> [node()]
Types Arg = silent | verbose
This function calls names(Host) for all hosts which are specified in the Erlang host file .hosts.erlang , collects the replies and
then evaluates ping(Node) on all those nodes. Returns the list of all nodes that were, successfully pinged.
Arg defaults to silent . If Arg == verbose , the function writes information about which nodes it is pinging to stdout.
This function can be useful when a node is started, and the names of the other nodes in the network are not initially known.
Failure: {error, Reason} if host_file() returns {error, Reason} .
world_list(Hosts) -> [node()]
world_list(Hosts, Arg) -> [node()]
Types Hosts = [Host]
Host = atom()
Arg = silent | verbose
As world/0,1 , but the hosts are given as argument instead of being read from .hosts.erlang .
FILES
The .hosts.erlang file consists of a number of host names written as Erlang terms. It is looked for in the current work directory, the
user's home directory, and $OTP_ROOT (the root directory of Erlang/OTP), in that order.
The format of the .hosts.erlang file must be one host name per line. The host names must be within quotes as shown in the following exam-
ple:
^ (new line)
Ericsson AB kernel 2.14.3 net_adm(3erl)