Is the non-global zone ip interface set to "shared"?
Both global and non-global zone look to be set to use "net0" so if the non-global zone requests "exclusive", it's not going to get it because the global zone is using it.
Thanks for your reply. How can I check to see if it is shared?
Also, the instructions I used to create a zone mention this:
Quote:
By default, all Oracle Solaris Zones are configured to have an automatic VNIC called anet, which gives us a network device automatically. We cannot see this network device yet, because it is automatically created when the zone is booted and also automatically destroyed on shutdown.
So I thought the interface should be automatically set up on the zone.
There might be some confusion because on the global zone the physical interface is also named net0, perhaps because the global zone is an LDom. So my global zone shows this:
While the aforementioned instructions show this:
Confusing for a network novice such as myself
I am seeking help from the gurus in this forum and hope that I can find answers soon. Anyone who provide the answers will be greatly appreciated.
I have a sparc box with Solaris 10 on it. We install Solaris with zone structure. One global zone and two other zone. I installed Oracle DB on global... (6 Replies)
Hi Everyone,
I have installed open solaris 10 on one of the x86 machines available but inspite of configuring the IP i am unable to access the machine through the network.
Can anyone please help me wih the settings required to access the machine across the network.Its really Urg..Any help is... (13 Replies)
Hi
i have created a solaris zone but have not yet connected any network cables for this new zone,
can i set the zone up without running the command 'add net' and not adding an ip or physical interface?
i tried to add dummy internet settings and get this
zonecfg:coddr> add net... (4 Replies)
I am trying to use a serial communications device that is connected to /dev/ttyb on a netra 240 server. This is a solaris zone configuration using solaris 10 0910. I am able to access /dev/ttyb from the global zone but not throught he non-global zone. I have enabled all of the tty devices in my... (0 Replies)
I am trying to create a branded 10 zone on a Solaris 11.1 control domain. I am using a flar image (cpio) from an existing LDOM. Here are the steps taken after flarcreate.
#zonecfg -z <device>
>create -b
>set brand=solaris10
>set zonepath=/zonez/<device>
>set ip-type=exclusive
>add net... (1 Reply)
Dear all,
recently, I migrated a solaris zone from one host to another. The zone was inside of a zpool. The zpool cotains two volumes.
I did the following:
host1:
$ zlogin zone1 shutdown -y -g0 -i0 #Zone status changes from running to installed
$ zpool export zone1
host2:
$ zpool... (2 Replies)
Have 2 nics on physical system
net0 phys 1500 up --
net1 phys 1500 up --
1. I want to create a link aggregation with LACP enabled with above 2 nics
2. Create port-group(Like we create on ESXi) with VLAN-ID 2141
3. And assign this... (0 Replies)
I am planning to do solaris 11 global zone patching having solaris 10 branded zone. I have a doubts on step 8 specially
Can someone clear my step 8 doubts or if anything wrong between step 1 to step 9 please correct that also as I have pretty good idea about Step 10 mean patching in solaris 10... (2 Replies)
Hi,
I have a Solaris 10 zone which I need to configure on a new network. I have configured the new IP on the zone itself and I can ping the interface from a node on the same network, but not from another network. Basically I need to know how to route the traffic from the zone to it's... (3 Replies)
Hi, hoping someone can help, its been a while since I used Solaris.
After creating a NGZ (non global zone), the NGZ can access the GZ (Global Zone) and the GZ can access the NGZ (using ssh, zlogin)
However, the NGZ cannot access any other netwqork devices, it can't even see the default router
... (2 Replies)
Discussion started by: GazinLincoln
2 Replies
LEARN ABOUT MOJAVE
suninstall
suninstall(1M) System Administration Commands suninstall(1M)NAME
suninstall - install the Solaris operating system
SYNOPSIS
suninstall
DESCRIPTION install-solaris(1M) is now the preferred command for starting and restarting the Solaris Installation program. It should be used instead of
suninstall. suninstall is symbolically linked to install-solaris.
suninstall is a forms-based and graphical subsystem for installing the operating system.
suninstall exists only on the Solaris installation media (CD or DVD) and should only be invoked from there. Refer to the Solaris 10 Instal-
lation Guide: Basic Installations for more details.
suninstall allows installation of the operating system onto any standalone system. suninstall loads the software available on the installa-
tion media. Refer to the Solaris 10 Installation Guide: Basic Installations for disk space requirements.
USAGE
Refer to the Solaris 10 Installation Guide: Basic Installations for more information on the various menus and selections.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcdrom (Solaris instal- |
| |lation media) |
+-----------------------------+-----------------------------+
SEE ALSO pkginfo(1), install(1M), install-solaris(1M), pkgadd(1M), attributes(5)
Solaris 10 Installation Guide: Basic Installations
NOTES
It is advisable to exit suninstall by means of the exit options in the suninstall menus.
SunOS 5.10 9 Sep 2004 suninstall(1M)