And I am unable to ping anything from the Local Zone except for the IP address of the global zone.
My global zone has an IP address of 10.25.63.55 and my local zone has an IP address of 10.25.63.69.
Global Zone
Code:
root@sol11:~# netstat -rn
Routing Table: IPv4
Destination Gateway Flags Ref Use Interface
-------------------- -------------------- ----- ----- ---------- ---------
default 10.25.63.1 UG 4 451672 net0
10.25.63.0 10.25.63.55 U 4 3 net0
127.0.0.1 127.0.0.1 UH 3 18679 lo0
root@sol11:~# ifconfig -a
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
net0: flags=1000943<UP,BROADCAST,RUNNING,PROMISC,MULTICAST,IPv4> mtu 1500 index 2
inet 10.25.63.55 netmask ffffff00 broadcast 10.25.63.255
ether 0:14:4f:f9:4:2b
lo0: flags=2002000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv6,VIRTUAL> mtu 8252 index 1
inet6 ::1/128
net0: flags=20002000941<UP,RUNNING,PROMISC,MULTICAST,IPv6> mtu 1500 index 2
inet6 fe80::214:4fff:fef9:42b/10
ether 0:14:4f:f9:4:2b
net0:1: flags=20002080941<UP,RUNNING,PROMISC,MULTICAST,ADDRCONF,IPv6> mtu 1500 index 2
inet6 2620:0:170:588:214:4fff:fef9:42b/64
root@sol11:~# dladm show-link
LINK CLASS MTU STATE OVER
net0 phys 1500 up --
testzone/net0 vnic 1500 up net0
Local Zone
Code:
root@zone:~# netstat -rn
Routing Table: IPv4
Destination Gateway Flags Ref Use Interface
-------------------- -------------------- ----- ----- ---------- ---------
default 10.25.63.1 UG 2 1443 net0
10.25.63.0 10.25.63.69 U 4 6 net0
127.0.0.1 127.0.0.1 UH 2 12 lo0
root@zone:~# ifconfig -a
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
net0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 3
inet 10.25.63.69 netmask ffffff00 broadcast 10.25.63.255
ether 2:8:20:47:cb:60
lo0: flags=2002000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv6,VIRTUAL> mtu 8252 index 1
inet6 ::1/128
net0: flags=20002000841<UP,RUNNING,MULTICAST,IPv6> mtu 1500 index 3
inet6 fe80::8:20ff:fe47:cb60/10
ether 2:8:20:47:cb:60
net0:1: flags=20002080841<UP,RUNNING,MULTICAST,ADDRCONF,IPv6> mtu 1500 index 3
inet6 2620:0:170:588:8:20ff:fe47:cb60/64
root@zone:~# dladm show-link
LINK CLASS MTU STATE OVER
net0 vnic 1500 up ?
root@zone:~# ipadm show-addr
ADDROBJ TYPE STATE ADDR
lo0/v4 static ok 127.0.0.1/8
net0/v4 static ok 10.25.63.69/24
lo0/v6 static ok ::1/128
net0/v6 addrconf ok fe80::8:20ff:fe47:cb60/10
net0/v6 addrconf ok 2620:0:170:588:8:20ff:fe47:cb60/64
I removed the IPv6 routing tables because they seemed irrelevant, but please let me know if they are necessary.
I am seeking help from the gurus in this forum and hope that I can find answers soon. Anyone who provide the answers will be greatly appreciated.
I have a sparc box with Solaris 10 on it. We install Solaris with zone structure. One global zone and two other zone. I installed Oracle DB on global... (6 Replies)
Hi Everyone,
I have installed open solaris 10 on one of the x86 machines available but inspite of configuring the IP i am unable to access the machine through the network.
Can anyone please help me wih the settings required to access the machine across the network.Its really Urg..Any help is... (13 Replies)
Hi
i have created a solaris zone but have not yet connected any network cables for this new zone,
can i set the zone up without running the command 'add net' and not adding an ip or physical interface?
i tried to add dummy internet settings and get this
zonecfg:coddr> add net... (4 Replies)
I am trying to use a serial communications device that is connected to /dev/ttyb on a netra 240 server. This is a solaris zone configuration using solaris 10 0910. I am able to access /dev/ttyb from the global zone but not throught he non-global zone. I have enabled all of the tty devices in my... (0 Replies)
I am trying to create a branded 10 zone on a Solaris 11.1 control domain. I am using a flar image (cpio) from an existing LDOM. Here are the steps taken after flarcreate.
#zonecfg -z <device>
>create -b
>set brand=solaris10
>set zonepath=/zonez/<device>
>set ip-type=exclusive
>add net... (1 Reply)
Dear all,
recently, I migrated a solaris zone from one host to another. The zone was inside of a zpool. The zpool cotains two volumes.
I did the following:
host1:
$ zlogin zone1 shutdown -y -g0 -i0 #Zone status changes from running to installed
$ zpool export zone1
host2:
$ zpool... (2 Replies)
Have 2 nics on physical system
net0 phys 1500 up --
net1 phys 1500 up --
1. I want to create a link aggregation with LACP enabled with above 2 nics
2. Create port-group(Like we create on ESXi) with VLAN-ID 2141
3. And assign this... (0 Replies)
I am planning to do solaris 11 global zone patching having solaris 10 branded zone. I have a doubts on step 8 specially
Can someone clear my step 8 doubts or if anything wrong between step 1 to step 9 please correct that also as I have pretty good idea about Step 10 mean patching in solaris 10... (2 Replies)
Hi,
I have a Solaris 10 zone which I need to configure on a new network. I have configured the new IP on the zone itself and I can ping the interface from a node on the same network, but not from another network. Basically I need to know how to route the traffic from the zone to it's... (3 Replies)
Hi, hoping someone can help, its been a while since I used Solaris.
After creating a NGZ (non global zone), the NGZ can access the GZ (Global Zone) and the GZ can access the NGZ (using ssh, zlogin)
However, the NGZ cannot access any other netwqork devices, it can't even see the default router
... (2 Replies)