Sponsored Content
Operating Systems Solaris Sun V445 hangs before {0} ok prompt Post 302879004 by hicksd8 on Tuesday 10th of December 2013 04:57:56 AM
Old 12-10-2013
See page 59 of attached document
 

9 More Discussions You Might Find Interesting

1. Solaris

Jumpstart Solaris 8 on Sun Blade 150 Hangs

We had to replace a hard drive in one of our Sun Blade 150s, but now it hangs during the Jumpstart. It will show 1 or 2 Timeout for ARP/RARP messages and then start the spinning numbers. It always stops at 2ae00 and just hangs there. We have 1 combined jumpstart server and it is also our NIS+... (5 Replies)
Discussion started by: stottsja
5 Replies

2. Solaris

How to get to a OK prompt on new SUN T5140

Hi, I have a brand new SUN T5140 machine. I am trying to install Solaris 10 on the box. When I go to the machine using a KVM session I can see a blank screen , how can I get to the OK prompt to start the installation. Thanks, Suresh (10 Replies)
Discussion started by: gunnervarma
10 Replies

3. Solaris

How to get to the OK prompt without Sun keyboard

Hi all, I have just replaced the HDD on a Ultra 5 Spark machine, now I need to reinstall Solaris 9. The problem is: how do I get to the OK prompt without a Sun keyboard in order to boot from CD? At moment when I power on the machine I get the following error: Timeout Waiting for ARP/RARP... (13 Replies)
Discussion started by: sspirito
13 Replies

4. Solaris

XSCF prompt disappeared, Sun M5000

Hi, I've got an issue here: After I logon to the xscf prompt of this Sun M5000 and did 'XSCF> version -c xcp', the xscf prompt disappeared. I can't get it back and can't log out. exit rebootxscf logout #. #> #> ~# ~# exit sendbreak exit I tried to set the Mode Switch to the service... (3 Replies)
Discussion started by: aixlover
3 Replies

5. Solaris

V445 unable to boot because of an error

This is what is displayed on the screen as the system tries to boot and then hangs: 0>Test CPU(s)....Done 0>Interrupt Crosscall....| SC Alert: DHCP negotiation failed, perhaps misconfigured or no DHCP server avail able Done 0>Init Memory....| SC Alert: Host System has Reset 'Done 0>PLL... (2 Replies)
Discussion started by: kenosongo
2 Replies

6. Solaris

Failure to boot v445

Hi Guys, I have a small problem with a v445 which I have been informed will only boot with the reconfigure option enabled. It is attached to HP SAN storage using qla2300 FCA's with a Veritas encapsulated rootvoldg (No Laughing here please) when I try a reboot I get the following error. ... (5 Replies)
Discussion started by: gull04
5 Replies

7. Solaris

Unable to move from rsc prompt to ok prompt

Hi, on sunfire v890 unable to move from rsc prompt to ok prompt, i have executed the command break. (9 Replies)
Discussion started by: manoj.solaris
9 Replies

8. Solaris

Rebuild/Reset to default Sun v445

Hello, I'm quite new to Unix but I've got an old Sun v445 server that was previously used as a backup database server, these have since been moved to new hardware. The old admin who configured the box has since retired and left no notes about it, so i have no idea what the root password is and... (2 Replies)
Discussion started by: dbajtr
2 Replies

9. Solaris

Install ext DLT Sun Tape drive on V445 Solaris 10

I have a SunFire V445 running Solaris 10 and am adding a Sun DLT tape drive. From the OK prompt the probe-scsi-all does see the drive and it is the proper target of 4. When I do the boot -- -r it does build the /dev/rmt directories correctly and the links to /devices appear correct as well. When I... (8 Replies)
Discussion started by: chastings
8 Replies
DEVICE(9)						   BSD Kernel Developer's Manual						 DEVICE(9)

NAME
device -- an abstract representation of a device SYNOPSIS
typedef struct device *device_t; DESCRIPTION
The device object represents a piece of hardware attached to the system such as an expansion card, the bus which that card is plugged into, disk drives attached to the expansion card etc. The system defines one device, root_bus and all other devices are created dynamically during autoconfiguration. Normally devices representing top-level busses in the system (ISA, PCI etc.) will be attached directly to root_bus and other devices will be added as children of their relevant bus. The devices in a system form a tree. All devices except root_bus have a parent (see device_get_parent(9)). In addition, any device can have children attached to it (see device_add_child(9), device_add_child_ordered(9), device_find_child(9), device_get_children(9), and device_delete_child(9)). A device which has been successfully probed and attached to the system will also have a driver (see device_get_driver(9) and driver(9)) and a devclass (see device_get_devclass(9) and devclass(9)). Various other attributes of the device include a unit number (see device_get_unit(9)), verbose description (normally supplied by the driver, see device_set_desc(9) and device_get_desc(9)), a set of bus-spe- cific variables (see device_get_ivars(9)) and a set of driver-specific variables (see device_get_softc(9)). Devices can be in one of several states: DS_NOTPRESENT the device has not been probed for existence or the probe failed DS_ALIVE the device probe succeeded but not yet attached DS_ATTACHED the device has been successfully attached DS_BUSY the device is currently open The current state of the device can be determined by calling device_get_state(9). SEE ALSO
devclass(9), driver(9) AUTHORS
This manual page was written by Doug Rabson. BSD
June 16, 1998 BSD
All times are GMT -4. The time now is 04:33 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy