12-06-2013
Hi,
tunneling needs setting up a router with an ipv4 address again. Can the same machine can be used for tunneling setup?
Thanks
Naveen
9 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
hello
i'm working on aix 5300-05-03 hacmp ver 5.4
well my issue is that when firewall (gateway to internet ) goes down my machine start to work very very slowly!!!
the output of the sniffer is that on the output card , my machine try to convert ipv4 to ipv6 0.0.2.0
my machine is not configure... (1 Reply)
Discussion started by: ariec
1 Replies
2. AIX
hello
i'm working on AIX 5300-05-03 P520 hacmp 5.4
when connection to the internet is going down , firewall down, my application work verey verey slowly!!! and on the sliffer output i'm got trys of my serevr to do convert from ipv4 ipv6 ( 0.0.2.0 and AAAAAAAA).
some one have an idea why... (1 Reply)
Discussion started by: ariec
1 Replies
3. Solaris
Hi folks, i hope you'll help me to configure my ipv6 tunnel.
First, i create my tunnel in:
Hurricane Electric Free IPv6 Tunnel Broker
My IP is 83.228.93.34
in HE:
------------------------
Server IPv4 address: 216.66.84.46
Server IPv6 address: 2001:470:1f14:16a::1/64
Client IPv4 address: ... (2 Replies)
Discussion started by: static
2 Replies
4. Shell Programming and Scripting
I have perl script that I use to check and ping a list of ip,
The problem is, I didnt understand how to ping ipv6 on perl,
Could I use Ping::External??And how could I get the ping result (reply or not)?
This is my code
#!/usr/bin/perl --
use Net::Ping;
use Data::Validate::IP;
use... (3 Replies)
Discussion started by: franzramadhan
3 Replies
5. Red Hat
Hello,
I was wondering if it would be possible to run two VMs one with services for IPv4 and the other one with services for IPv6. The main physical system would be connected to a IPv6 switch.
I think it should be fine but I would like to hear out your comments. (1 Reply)
Discussion started by: svalenciatech
1 Replies
6. Solaris
Hi
I am looking to have an NTP server that will support both ipv4 and ipv6 clients. Is there anything specific about the configuration that I should be looking at? (7 Replies)
Discussion started by: eeisken
7 Replies
7. Solaris
Hi
I am looking to set-up ISC DHCP to support ipv6, and to migrate my existing SUN DHCP ipv4 to ISC,
finding the ipv4 options for the SUN DHCP options was ok eg
TFTPsrvN = tftp-server-name
OptBootF = bootfile-name
However if I set up a DHCPv6 does anyone know what the equivalent... (1 Reply)
Discussion started by: eeisken
1 Replies
8. AIX
Hi all,
I have setup ipv6 in AIX machine using autoconf6 command.
I was successfull in doing this. after execution of the command local link address was assigned to one of the interfaces
(en1).But I have to setup the following environment as well.
1) Machine with only IPv6 support(IPv4... (0 Replies)
Discussion started by: ard
0 Replies
9. Solaris
Hello dears
how to assign IPv4 and IPv6 addresses with same interface on solaris 10 (1 Reply)
Discussion started by: ttashman
1 Replies
LEARN ABOUT SUSE
kismet_drone
kismet_drone(1) kismet_drone(1)
NAME
kismet_drone - Wireless sniffing and monitoring remote drone
SYNOPSIS
kismet_drone [-svh] [-f config-file] [-c capture-source]
[-C enable-capture-sources] [-p port] [-a allowed-hosts]
[-N server-name]
DESCRIPTION
kismet_drone supports all the capture sources available to Kismet. Instead of processing packets locally, kismet_drone makes them avail-
able via TCP to a remote kismet_server using the 'drone' capture source.
USAGE
kismet_drone should be configured as you would kismet_server. All logging, packet dissection, etc will take place on the remote kismet
server using the 'drone' capture source.
kismet_monitor should be used to place capture sources into rfmonitor mode as needed, and kismet_hopper should be used for channel hopping.
kismet_drone is controlled by the kismet_drone.conf config file.
ENCRYPTION
It may be desireable to encrypt the packet stream between the remote drone and the kismet system. Standard SSH packet tunneling or any
other tunneling/forwarding system may be used, and is recommended.
SEE ALSO
kismet(1), kismet_drone.conf(5)
AUTHOR
Mike Kershaw
February 24, 2002 kismet_drone(1)