12-04-2013
So how have you IP connectivity between these two hosts at present?
9 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
hello
i'm working on aix 5300-05-03 hacmp ver 5.4
well my issue is that when firewall (gateway to internet ) goes down my machine start to work very very slowly!!!
the output of the sniffer is that on the output card , my machine try to convert ipv4 to ipv6 0.0.2.0
my machine is not configure... (1 Reply)
Discussion started by: ariec
1 Replies
2. AIX
hello
i'm working on AIX 5300-05-03 P520 hacmp 5.4
when connection to the internet is going down , firewall down, my application work verey verey slowly!!! and on the sliffer output i'm got trys of my serevr to do convert from ipv4 ipv6 ( 0.0.2.0 and AAAAAAAA).
some one have an idea why... (1 Reply)
Discussion started by: ariec
1 Replies
3. Solaris
Hi folks, i hope you'll help me to configure my ipv6 tunnel.
First, i create my tunnel in:
Hurricane Electric Free IPv6 Tunnel Broker
My IP is 83.228.93.34
in HE:
------------------------
Server IPv4 address: 216.66.84.46
Server IPv6 address: 2001:470:1f14:16a::1/64
Client IPv4 address: ... (2 Replies)
Discussion started by: static
2 Replies
4. Shell Programming and Scripting
I have perl script that I use to check and ping a list of ip,
The problem is, I didnt understand how to ping ipv6 on perl,
Could I use Ping::External??And how could I get the ping result (reply or not)?
This is my code
#!/usr/bin/perl --
use Net::Ping;
use Data::Validate::IP;
use... (3 Replies)
Discussion started by: franzramadhan
3 Replies
5. Red Hat
Hello,
I was wondering if it would be possible to run two VMs one with services for IPv4 and the other one with services for IPv6. The main physical system would be connected to a IPv6 switch.
I think it should be fine but I would like to hear out your comments. (1 Reply)
Discussion started by: svalenciatech
1 Replies
6. Solaris
Hi
I am looking to have an NTP server that will support both ipv4 and ipv6 clients. Is there anything specific about the configuration that I should be looking at? (7 Replies)
Discussion started by: eeisken
7 Replies
7. Solaris
Hi
I am looking to set-up ISC DHCP to support ipv6, and to migrate my existing SUN DHCP ipv4 to ISC,
finding the ipv4 options for the SUN DHCP options was ok eg
TFTPsrvN = tftp-server-name
OptBootF = bootfile-name
However if I set up a DHCPv6 does anyone know what the equivalent... (1 Reply)
Discussion started by: eeisken
1 Replies
8. AIX
Hi all,
I have setup ipv6 in AIX machine using autoconf6 command.
I was successfull in doing this. after execution of the command local link address was assigned to one of the interfaces
(en1).But I have to setup the following environment as well.
1) Machine with only IPv6 support(IPv4... (0 Replies)
Discussion started by: ard
0 Replies
9. Solaris
Hello dears
how to assign IPv4 and IPv6 addresses with same interface on solaris 10 (1 Reply)
Discussion started by: ttashman
1 Replies
AICCU(1) AICCU(1)
NAME
AICCU - Automatic IPv6 Connectivity Configuration Utility
SYNOPSIS
aiccu <start|stop|tunnels|test|autotest|license> [ config ]
DESCRIPTION
AICCU makes it very easy for anybody to get IPv6 connectivity everywhere they want. It uses the TIC (Tunnel Information & Control) protocol
to request the information needed to setup a tunnel through which the connectivity is created. AICCU supports the following tunneling pro-
tocols: - 6in4 static (RFC 2893) - 6in4 heartbeat (RFC 2893 + draft-massar-v6ops-heartbeat) - tinc (http://www.tinc-vpn.org) -
AYIYA (draft-massar-v6ops-ayiya) As AYIYA even works from behind NAT's, thus unless there is a very restrictive firewall in place,
anybody should be able to get IPv6 connectivity without problems and everywhere they want.
OPTIONS
start Starts aiccu service.
stop Stops aiccu service.
tunnels
Prints a list of currently available tunnels.
test Builds the connection and runs a simple selftest allowing a user to report this back as it should show most obvious problems.
autotest
Decription here
license
Shows the license aiccu is released under.
config Read the configuration from config file.
SEE ALSO
The AICCU page <URL:http://www.sixxs.net/tools/aiccu/> at sixxs.
AUTHOR
AICCU was written by Jeroen Massar with contributions supplied a number of people as mentioned in the Changelog.
18 April 2005 AICCU(1)