I've been tasked to implement ntp on my SCO Unix servers. I have over 600 servers spread across the US in different time zones. Each remote server has network connectivity to a main server here, through their local ISP. (That's how we currently deliver mail to them).
My question is, how can... (5 Replies)
We have configured most of 1200 servers with an NTP server.
For the rest of the servers, I have a strange requirement.
I want to synchronize them with NTP time with a lag of 15 minutes. Is it possible ? If yes How ? (0 Replies)
Ok, I have 4 production systems. There is one NTP server for all four systems. In each system there is one Solaris 10 box that points to that NTP server. All of the other machines in the system point to the Solaris 10 machine to get their time sync.
All four Solaris 10 machines have essentially... (2 Replies)
All here, thank you for listening. Now I've set up a Linux NTP server by adding a external windows NTP server in /etc/ntp.conf. Then I start the ntpd daemon. But how often does the Linux NTP server update its time with the external NTP server? I've looked up everywhere but found no information... (1 Reply)
hello all,,
am trying to do a time synchronization between a ntp server and a client, but facing some problems in doing so:
i run the ntpdate in debug mode and this is what i got. please help me out..
# ntpd -d -u 172.22.1.207
ntpd 4.2.2p1@1.1570-o Sun Aug 28 19:21:03 UTC 2011 (1)... (1 Reply)
Good morning,
My first post and first visit, so hello. I have been asked to see if one of our Linux boxes can have it's time sync automatically because the person who built the system has told our staff it cannot be done. To me that raised some flags because although I am no Linux expert, I just... (12 Replies)
There is one server in my company where the time is out of sync.
When I checked (compared with other servers whose time is correct), the XNTPD variable in /etc/rc.config.d/netdaemons was set as 0.
I changed this to 1, and tried restarting the xntpd process with :
# /sbin/init.d/xntpd start
... (4 Replies)
Hello,
one of my clients has the following task for me:
To write a Perl script that checks, whether ntp is active on a particular AIX or Linux box.
Obviously the last synchronization is logged in the file ntp.log
So, my task would be find out, when the synchronization SHOULD have taken... (1 Reply)
Discussion started by: Bloehdian1
1 Replies
LEARN ABOUT ULTRIX
ntp.conf
ntp.conf(5) File Formats Manual ntp.conf(5)Name
ntp.conf - Network Time Protocol configuration file
Description
The file is the configuration file for the Network Time Protocol (NTP) daemon, This file must be configured on your system before running
Any host names that you specify in the file must have an entry in the file, or an entry in the master database, if the database is being
served to your system by BIND/Hesiod or Yellow Pages.
The file has four entry formats:
trusting no
This entry guarantees that your system synchronizes only to the NTP servers identified in the peer and server entries specified. Dig-
ital recommends that all systems include the entry.
peer server
This entry identifies server as one of the NTP servers that your system trusts, and from which your system will accept time synchro-
nization. Your system may also provide time synchronization to this server. Servers can be identified by host name or internet
address.
NTP servers should be configured with entries.
server server
This entry identifies server as one of the NTP servers that your system trusts, and from which your system will accept time synchro-
nization. Your system can not provide time synchronization to this server. Servers can be identified by host name or internet
address.
NTP clients should be configured with entries.
peer /dev/null LOCL 1 -5 local
This entry identifies your system as a local reference clock. A local reference clock is the most accurate system clock available at
your site. If you receive time synchronization from the Internet NTP service, you should not include this entry on any of your sys-
tems. At most, one system in a set of nodes running should be identified as a local reference clock.
A host which specifies this entry should not specify any or entries.
Examples
This is a sample configuration file for an NTP client which receives time synchronization from the NTP servers: and Lines beginning with a
number sign (#) are comments.
#
# NTP Configuration File
# This file is mandatory for the ntpd daemon
#
#
#
# ** A L L **
#
# "trusting no" prevents this host from synchronizing
# to any host that is not listed below. It is recommended
# that all hosts include the line "trusting no".
#
trusting no
#
#
# ** S E R V E R **
#
# If you are configuring a server, use "peer" entries to
# synchronize to other NTP servers. For example, server1,
# server2, and server3.
#
#peer server1
#peer server2
#peer server3
#
#
#
#
# ** C L I E N T **
#
# If you are configuring a client, use "server" entries to
# synchronize to NTP servers. For example, server1, server2,
# and server3.
#
server server1
server server2
server server3
#
#
#
# ** L O C A L R E F E R E N C E C L O C K **
#
# If you are configuring a local reference clock, include the
# following entry and the "trusting no" entry ONLY.
#
#peer /dev/null LOCL 1 -5 local
#
See Alsontp(1), ntpd(8), ntpdc(8)
RFC 1129--Internet time synchronization: The Network Time Protocol
Introduction to Networking and Distributed System Services
ntp.conf(5)