11-22-2013
Difference between lpar and lun
Hello,
What's the difference between lpar and a lun?
Best regards,
Vishal
10 More Discussions You Might Find Interesting
1. AIX
Hello guys,
It would be so nice of you if someone can provide me with these informations.
1) My SAN group assigned 51G of LUN space to the VIO server.I ran cfgdev to discover the newly added LUN. Unfortunately most of the disks that are in VIO server is 51G. How would I know which is the newly... (3 Replies)
Discussion started by: solaix14
3 Replies
2. Solaris
I have a list of LUN ID, my task is to find if disk has been added or not. How do I do that? I have been searching the forum and not able to find answer.
thanks (4 Replies)
Discussion started by: uuontario
4 Replies
3. AIX
I am planning for System P with 2 number of 2-core processor (4 core in total).
Can I make 3 LPARS with this processor configuration without the support of micropartitioning, that means with simple LPAR only. (3 Replies)
Discussion started by: pchangba
3 Replies
4. AIX
Hi all,
I have the following configuration
2 ds3524 storage disk systems located over 2 locations
2 P720 server located over 2 locations
DS3524 are connected to san switch.
Each vio server has 1 fc adapter attached to a san switch.
per p720 server 2 virtual io servers. Vio 1 has 1 lun... (2 Replies)
Discussion started by: markiemark
2 Replies
5. AIX
Hi All,
Besides the licenses on VIO and LPAR. What's the main difference with the two? I have installed VIO, my manager told me so, because it's like a free hypervisor but I never installed LPAR before. How do you install it? And if you can give more info on the two, that would be great.
... (5 Replies)
Discussion started by: itik
5 Replies
6. AIX
Hi,
I would like to know how to share lun in between 2 lpars.
I have run tbe below command on vio server.
/usr/sbin/chdev -l hdisk1 -a reserve_policy=no_reserve
after above command I am able to assign lun on one Lpar. but it is not visible to other lpar.
even after this I have run... (3 Replies)
Discussion started by: manoj.solaris
3 Replies
7. Programming
I think both write at the end of the file ......
but is there a sharp difference between those 2 instruction .....
thank you
this is my 3rd question today forgive me :D (1 Reply)
Discussion started by: fwrlfo
1 Replies
8. AIX
We have a 2 node oracle rac cluster one node is in frame 1 and other is in frame 2
Now,because of some hardware failure(processor card and cable) in frame 1 we will failover database services from lpar in frame 1 to lpar(oracle rac cluster node2) in frame2 and the entire replacement of hardware... (9 Replies)
Discussion started by: admin_db
9 Replies
9. AIX
There can be configurations in IBM Server wherein a
standalone partition is created on some supported IBM Server
Or
A VIOS - VIOC LPARs created.
Now in both cases they are lpars. But if I want to differentiate b/w a standalone LPAR vs an VIOC LPAR how can I do..?
On a... (2 Replies)
Discussion started by: Manish00712
2 Replies
10. Shell Programming and Scripting
In the awk I am trying to subtract the difference $3-$2 of each matching $4 before the first _ (underscore) and print that value in $13.
I think the awk will do that, but added comments. What I am not sure off is how to add a line or lines that will add sum each matching $13 value and put it in... (2 Replies)
Discussion started by: cmccabe
2 Replies
LEARN ABOUT SUSE
openipmicmd
openipmicmd(1) An IPMI Command Interface openipmicmd(1)
NAME
openipmicmd - An IPMI Command Interface
SYNOPSIS
openipmicmd [-k entry-to-execute] <connection parms>
DESCRIPTION
The openipmicmd program allows a user to execute direct IPMI commands. It can work with direct interface with the OpenIPMI driver or with
IPMI LAN interfaces.
OPTIONS
-k entry-to-execute
Execute a single command an exit.
<connectionparms>
The parameters for the connection depend on the connection type. These are all described in openipmi_conparms (7)
COMMANDS
Once up, you can execute commands in the user interface. Note that commands and responses are asynchronous, you issue a command and the
interface returns immediately. When the response comes back, it will be dumped on your console. That's a little strange looking, but IPMI
is ansychronous underneath. Note that the -k option is synchronous, it will wait for the response or a timeout before returning.
0f lun netfn cmd [data1 [data2 ...]]
Send a command to the BMC you are connected to.
channel [ipmb] IPMB-addr lun netfn [seq] cmd [data1 [data2 ...]]
Send a command to a device on the IPMB bus. The "ipmb" string is optional. The seq must be provided if the netfn is a response (an
odd number). It must be the same sequence number that came in on the command in the "Command Sequence = seq" part of the command.
channel 00 IPMB-addr lun netfn cmd [data1 [data2 ...]]
Send a broadcast command to a device on the IPMB bus.
channel lan handle remote-swid local-swid lun netfn cmd [data1 [data ...]]
Send a command to a device over a LAN channel. Note that this not the same as a LAN connection. This sends a message through a
local BMC to a remote system that is hooked up with a LAN connection.
test_lat count command
Executes the given commands (one of the previous commands) count times and gives the average time per command to execute. Note that
"count" is hexadecimal.
help Display some help.
regcmd netfn cmd
Register to receive the given command. If the driver receives an external command, it will print it out. This only works with sys-
tem interface connections, it will not work on LAN connections.
unregcmd netfn cmd
Remove a command registration.
SEE ALSO
ipmi_ui(1), ipmilan(8), openipmi_conparms(7)
KNOWN PROBLEMS
The asychronous nature of the program can be annoying.
AUTHOR
Corey Minyard <cminyard@mvista.org>
OpenIPMI 05/13/03 openipmicmd(1)