I'm a little worried about the label part being a bit short. What happens if you have:-
The method I have given should work okay, but it uses the full directory name. Is that a problem?
Hi,
I want to replace the contents of a file.I tried using :
sed 's/01514581/01514582/' $p
where 01514581 is the original value
01514582 is the replaced value
$p is the file name (captured in a variable)..
The output does not recognise $p
If you give :
sed... (2 Replies)
Hi
I have a file that looks like this:
Line 0
animal elephant
Line 1
animal elephant
Line 2
animal elephant
Line 3
animal elephant
What i am aiming to do is with a script and an input value of... (6 Replies)
From the existing file, I need to replace specific contents possibly with var every time when the user changes the var.
e.g the contents in the file file.txt is 'My name is $n and I am $y years old' and every time user changed the var outside the file, the contents of the file should be created... (4 Replies)
Hi All,
Need help on this
I have 2 files
one file file1 which has several entries as :
define service{
hostgroup_name !host1,!host5,!host6,.*
service_description check_nrpe
}
define service{
hostgroup_name !host2,!host4,!host6,.*
service_description check_opt
}
another... (2 Replies)
Hi,
I am facing issue while reading data from a file in UNIX. my requirement is to compare two files and for the text pattern matching in the 1st file, replace the contents in second file by the contents of first file from start to the end and write the contents to thrid file.
i am able to... (2 Replies)
Hi Friends,
I have a file1 with 5 columns
a b c d e
f g h i j
I have file2 with 3 columns
1 2 3
4 5 6
I want to replace 3rd 4th and 5th columns in file1 with file2 contents, so the output would be
a b 1 2 3
f g 4 5 6
Thanks (6 Replies)
How can i replace the contents in a particular line of a file.
<FOLDERMAP SOURCEFOLDERNAME="FFCB-2012" SOURCEREPOSITORYNAME="Repo_DEV" TARGETFOLDERNAME="TEST" TARGETREPOSITORYNAME="Dev_Repo"/>
For Example I want to replace the SOURCEREPOSITORYNAME="Repo_DEV" to... (3 Replies)
Hello,
I have two files: file1 and file2
file1 has the following info:
---
host: "localhost"
port: 3000
reporter_type: "zookeeper"
zk_hosts:
- "localhost:2181"
file2 contains an IP address (1.1.1.1)
What I want to do is replace localhost with 1.1.1.1, so that the... (4 Replies)
Discussion started by: Jay Kah
4 Replies
LEARN ABOUT DEBIAN
raidfile-config
RAIDFILE-CONFIG(8) Box Backup RAIDFILE-CONFIG(8)NAME
raidfile-config - Configure Box Backup's RAID files
SYNOPSIS
raidfile-config config-dir blocksize dir1 [dir2 [dir3]]
DESCRIPTION
raidfile-config creates a raidfile.conf file for Box Backup. This file holds information about the directories used to store backups in.
Box Backup supports userland RAID, in a restricted RAID5 configuration, where 3 and only 3 'drives' are supported. You can read more about
RAID5 (and other RAID-levels) here[1].
Parameters
The parameters are as follows:
config-dir
The directory path where configuration files are located. Usually this is /etc/box. raidfile.conf will be written in this directory.
blocksize
The block size used for file storage in the system, in bytes. Using a multiple of the file system block size is a good strategy.
Depending on the size of the files you will be backing up, this multiple varies. Of course it also depends on the native block size of
your file system.
dir1
The first directory in the built-in RAID array.
dir2
The second directory in the built-in RAID array. If you are not using the built-in RAID functionality, this field should be ignored.
You should not use the built-in RAID if you have a hardware RAID solution or if you're using another type of software RAID (like md on
Linux).
dir3
The third directory in the built-in RAID array. The same notes that apply to dir2 also apply to dir3.
Note that there are currently no way to add multiple disk sets to the raidfile.conf file using command line tools, etc. See
raidfile.conf(5) for details on adding more disks.
BUGS
If you find a bug in Box Backup, and you want to let us know about it, join the mailing list[2], and send a description of the problem
there.
To report a bug, give us at least the following information:
o The version of Box Backup you are running
o The platform you are running on (hardware and OS), for both client and server.
o If possible attach your config files (bbstored.conf, bbackupd.conf) to the bug report.
o Also attach any log file output that helps shed light on the problem you are seeing.
o And last but certainly not least, a description of what you are seeing, in as much detail as possible.
FILES
raidfile-config generates the raidfile.conf(5) file.
SEE ALSO bbstored-config(8), bbstored.conf(5), raidfile.conf(5)AUTHORS
Ben Summers
Per Thomsen
James O'Gorman
NOTES
1. here
http://en.wikipedia.org/wiki/Redundant_array_of_independent_disks#RAID_5
2. mailing list
http://lists.warhead.org.uk/mailman/listinfo/boxbackup
Box Backup 0.11 10/28/2011 RAIDFILE-CONFIG(8)