11-12-2013
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
We have a Sun Sparc System which has multiple CPUs (4 Nos.). I need a command/program that can be used to monitor the % utilization per CPU. (2 Replies)
Discussion started by: saood
2 Replies
2. Linux
Hi All,
Kindly help me in optimizing the server as it displays a great amount of CPU & MEM being utilised when the mysql process executes.
Below are the stats ---
--------------------------------------------------------------------------
# top
15:51:57 up 23:22, 5 users, load average:... (1 Reply)
Discussion started by: gautamatul82
1 Replies
3. UNIX for Dummies Questions & Answers
Hi,
I want to check the CPU and Memory Utilisation in the whole machine (not for a single process). Can someone send me a ready made script which captures all information in a log every 5min??
Thanks,
Ajith (0 Replies)
Discussion started by: Ajith Praveen
0 Replies
4. Shell Programming and Scripting
Hi all,
I am a newbie to whole shell scripting thing. I deal with computational studies and a lot of softwares which run on linux. At times, I have to schedule my jobs after some process has started. In these case, I have to use at command to schedule my job.
However, I would like to know if... (0 Replies)
Discussion started by: johnsmithgr8
0 Replies
5. AIX
Hi,
I collect statistics with nmon. I'm very suprised about % wait of processor.
Number Of Processors: 4
Processor Clock Speed: 4204 MHz
Do U have an idea about % wait ?
│ 0----------25-----------50----------75----------100 ... (1 Reply)
Discussion started by: tagger
1 Replies
6. AIX
Hi,
We need to monitor one process over time to see at which exact point it starts to consume to much memory and CPU (to correlate this with some other events).
I am a newbie in AIX, so please could you tell me which command will give a snapshot of the current state of a process so that I... (1 Reply)
Discussion started by: yallow
1 Replies
7. UNIX for Dummies Questions & Answers
Hi all,
I'm using Solaris 10 and have an occasional problem where a process that runs near to midnight each day, takes anywhere between 30 seconds and over two minutes to complete. I suspect that the CPU is highly utilised during the times where it takes a long time to complete, but I need a way... (3 Replies)
Discussion started by: wthomas
3 Replies
8. UNIX for Dummies Questions & Answers
Hi ,
I need to find the average percentage of CPU utilisised by a particular process through a shell script. Suppose if a process is running for 6 hours i need to get average CPU utilised by it.
Could you please assist me.
Thanks, (0 Replies)
Discussion started by: praviper
0 Replies
9. Solaris
Hi,
Can anyone tell me how to get the CPU utilisation for past 1 day in Solaris.
Below is the version i m using
SunOS ss1qeb 5.10 Generic_138889-03 i86pc i386 i86pc
thanks in advance (2 Replies)
Discussion started by: ali560045
2 Replies
10. Shell Programming and Scripting
Hi,
I want to write one script that sent mail when CPU utilisation is more then 70%. i used topas but problem is it will show output only when we press ctrl +c.
Please let me know if there is some other command that will give cpu utilisation which i can use in shell script.
Thanks (3 Replies)
Discussion started by: ranvijaidba
3 Replies
IRSEND(1) FSF IRSEND(1)
NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.8.7pre1 May 2010 IRSEND(1)