Sponsored Content
Special Forums Hardware Filesystems, Disks and Memory Ask concept soft partition vs hard partition Post 302871521 by cjcox on Wednesday 6th of November 2013 10:35:35 AM
Old 11-06-2013
You can think of soft partitioning as a logical partition. It's a feature of the volume manager that Solaris provides. A hard partition will usually be "faster", but a lot depends on how you have things configured to begin with.

Soft partitions, because they are more abstract can be viewed as "friendlier" or "more flexible".

IMHO, if performance is a must, then you're likely going to be going SSD, etc...

So personally, I prefer the flexibility that soft partitioning provides. Obviously things that are wanting a true partition (some enterprise software may require it) you'll have no choice.

There's a chicken and egg problem with things under Solaris volume management, so there are still places like early on in the boot where hard partitions are going to be required. Depending on the complexity of your storage, it may also have that kind of requirement. But, after boot, if all visible as disk... I say pool it up and carve it up logically.

Just my two cents.
This User Gave Thanks to cjcox For This Post:
 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Partition Hard drive

Hello everyone. I am new to Linux so hope some one could help me here. I have a 30 Gb HD and windows Xp is my O/S, HD is not partitioned,but I want to Partitioned it, so I could Install Knoppix(Linux)on one of the partitioned one, how could I do this? OR should I erase every thing and then... (1 Reply)
Discussion started by: amir
1 Replies

2. UNIX for Dummies Questions & Answers

I've created a partition with GNU Parted, how do I mount the partition?

I've created a partition with GNU Parted, how do I mount the partition? The manual information at http://www.gnu.org/software/parted/manual/parted.html is good, but I am sure about how I mount the partition afterwards. Thanks, --Todd (1 Reply)
Discussion started by: jtp51
1 Replies

3. UNIX for Advanced & Expert Users

Hard-disk partition is Full problem?

HI, Currently I am working in One of the webhosting company and I found on one of my server "/home" partition is getting full say 105% usage... But when I actually check the partition size using "du -h", exact partition utilization is only 60-70%. So... (1 Reply)
Discussion started by: jagdish.machhi@
1 Replies

4. Solaris

Puzzled over over the relationship between the partition and geometry of hard disk.

Not sure why solaris couldn't detect the geometry of a hard disk which has a working OS of winxp pro. Is it due to the different OS that the partition information is stored in different location? When I type '"format" it is shown as below, c3d1 < drive type unknown>... (5 Replies)
Discussion started by: just.srad
5 Replies

5. Solaris

Need advice on soft partition

Hello All, Am trying to expand the soft partition which is in mirror. Am getting following error. Whether is it possible? or i am doing wrongly. Please assist. bash-2.05# metastat d100 d100: Mirror Submirror 0: d102 State: Okay Submirror 1: d105 State: Okay ... (7 Replies)
Discussion started by: gowthamakanthan
7 Replies

6. Solaris

Replacing a hard disk (SVM) with a soft partition?

The following is the summarry:- 1) Four disks in server ie (c1t0d0. c1t1d0, c1t2d0, c1t3d0). c1t2d0 is the disk to be replaced. c1t0d0 and c1t2d0 are mirrors. c1t1d0 and c1t3d0 are mirrors. Metadb to be deleted is in c1t2d0s7 a) Mirror d35 has 2 submirrors d38 and d39 d38 is a stripe... (0 Replies)
Discussion started by: aji1729
0 Replies

7. Solaris

Rename soft partition

Hi folks, is there any possibility how to rename soft partitions?? Here I found that this is not possible (I know that it is) but I need do it in some supported way. http://dlc.sun.com/osol/docs/content/LOGVOLMGRADMIN/tasks-basics-5.html This is production system it is why I need do it... (0 Replies)
Discussion started by: brusell
0 Replies

8. Solaris

Partition overlaps another partition while creating new parition in solaris

hi all while formatting hard disk i am getting following error. Partition 1 ends at 266338338 It must be between 34 and 143374704. label error: EFI Labels do not support overlapping partitions Partition 8 overlaps partition 1. Warning: error writing EFI. Label failed. I have formatted the... (2 Replies)
Discussion started by: nikhil kasar
2 Replies

9. Red Hat

Shrink LVM partition & create new Linux Primary partition

Hello All, I have a Red Hat Linux 5.9 Server installed with one hard disk & 2 Partitions created on it as follows, /boot - Linux Partition & another is LVM - One VG & under that 5-6 Logical volumes(var,opt,home etc). Here my requirement is to take out 1GB of space from LVM ( Any logical... (5 Replies)
Discussion started by: gr8_usk
5 Replies

10. Solaris

Extend a soft partition

Hi, I need to extend a soft partition from 20G to 100G. New disk is already added as a meta device. This soft partition is already assigned to a guest LDOM. Can someone let me know the steps to increase soft partition so guest LDOM can recognize the new space. Thanks (1 Reply)
Discussion started by: Gho
1 Replies
HD(4)							     Linux Programmer's Manual							     HD(4)

NAME
hd - MFM/IDE hard disk devices DESCRIPTION
The hd* devices are block devices to access MFM/IDE hard disk drives in raw mode. The master drive on the primary IDE controller (major device number 3) is hda; the slave drive is hdb. The master drive of the second controller (major device number 22) is hdc and the slave hdd. General IDE block device names have the form hdX, or hdXP, where X is a letter denoting the physical drive, and P is a number denoting the partition on that physical drive. The first form, hdX, is used to address the whole drive. Partition numbers are assigned in the order the partitions are discovered, and only nonempty, nonextended partitions get a number. However, partition numbers 1-4 are given to the four partitions described in the MBR (the "primary" partitions), regardless of whether they are unused or extended. Thus, the first logi- cal partition will be hdX5. Both DOS-type partitioning and BSD-disklabel partitioning are supported. You can have at most 63 partitions on an IDE disk. For example, /dev/hda refers to all of the first IDE drive in the system; and /dev/hdb3 refers to the third DOS "primary" partition on the second one. They are typically created by: mknod -m 660 /dev/hda b 3 0 mknod -m 660 /dev/hda1 b 3 1 mknod -m 660 /dev/hda2 b 3 2 ... mknod -m 660 /dev/hda8 b 3 8 mknod -m 660 /dev/hdb b 3 64 mknod -m 660 /dev/hdb1 b 3 65 mknod -m 660 /dev/hdb2 b 3 66 ... mknod -m 660 /dev/hdb8 b 3 72 chown root:disk /dev/hd* FILES
/dev/hd* SEE ALSO
chown(1), mknod(1), sd(4), mount(8) COLOPHON
This page is part of release 3.44 of the Linux man-pages project. A description of the project, and information about reporting bugs, can be found at http://www.kernel.org/doc/man-pages/. Linux 1992-12-17 HD(4)
All times are GMT -4. The time now is 12:36 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy