11-05-2013
You could create a new NIC for the Global and then assign it to the local.
I can't help with virtualbox, I've never used it before. But again, to my opinion, you need a device dedicated to your local to accomplish what you're describing.
9 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Does any body knows how to force NIC to 100 Full Duplex in Solaris 8, should survive after reboot or shutdown. (1 Reply)
Discussion started by: s_aamir
1 Replies
2. Cybersecurity
Does any body knows how to force NIC to 100 Full Duplex in Solaris 8, should survive after reboot or shutdown. (2 Replies)
Discussion started by: s_aamir
2 Replies
3. Solaris
Hi all,
I tried to use this command
ndd -set /dev/eri adv_1000fdx_cap 1
but i get a "operation failed, Invalid argument"
anyone can help ? Thanks (5 Replies)
Discussion started by: DarReNz
5 Replies
4. IP Networking
I have a TOSHIBA AS7000 B150 Sun Box
I wanted to run it with 100M/full duplex
I had added this to the /etc/system file to make to setting permenant So it would be set correctly on reboot.
set eri:eri_adv_100fdx_cap=1
set eri:eri_adv_100hdx_cap=0
set eri:eri_adv_autoneg_cap=0
But when I... (4 Replies)
Discussion started by: AirWalker83
4 Replies
5. Solaris
Hello all,
I`ve the following problem - I cannot start inetd in any way possible:
bash-3.00# svcs inetd
STATE STIME FMRI
offline Jul_30 svc:/network/inetd:default
bash-3.00#
bash-3.00# svcadm enable -r inetd
bash-3.00# svcs inetd
STATE STIME FMRI... (6 Replies)
Discussion started by: click
6 Replies
6. Solaris
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
Discussion started by: vectrum
0 Replies
7. UNIX for Advanced & Expert Users
Dear all,
recently, I migrated a solaris zone from one host to another. The zone was inside of a zpool. The zpool cotains two volumes.
I did the following:
host1:
$ zlogin zone1 shutdown -y -g0 -i0 #Zone status changes from running to installed
$ zpool export zone1
host2:
$ zpool... (2 Replies)
Discussion started by: custos
2 Replies
8. Solaris
I am planning to do solaris 11 global zone patching having solaris 10 branded zone. I have a doubts on step 8 specially
Can someone clear my step 8 doubts or if anything wrong between step 1 to step 9 please correct that also as I have pretty good idea about Step 10 mean patching in solaris 10... (2 Replies)
Discussion started by: amity
2 Replies
9. UNIX for Beginners Questions & Answers
I'm trying to migrate a Solaris 10 flar archive from a Sun M3000 to a T4-1. When I first created the zone I followed the Oracle instructions here: Transitioning an Oracle Solaris 10 Instance to an Oracle Solaris 11 System - Transitioning From Oracle Solaris 10 to Oracle Solaris 11 That worked... (6 Replies)
Discussion started by: Michele31416
6 Replies
LEARN ABOUT MOJAVE
qmail-users
qmail-users(5) File Formats Manual qmail-users(5)
NAME
qmail-users - assign mail addresses to users
OVERVIEW
The file /var/lib/qmail/users/assign assigns addresses to users. For example,
=joe.shmoe:joe:503:78:/home/joe:::
says that mail for joe.shmoe should be delivered to user joe, with uid 503 and gid 78, as specified by /home/joe/.qmail.
Assignments fed to qmail-newu will be used by qmail-lspawn to control qmail-local's deliveries. See qmail-newu(8). A change to
/var/lib/qmail/users/assign will have no effect until qmail-newu is run.
STRUCTURE
/var/lib/qmail/users/assign is a series of assignments, one per line. It ends with a line containing a single dot. Lines must not contain
NUL.
SIMPLE ASSIGNMENTS
A simple assignment is a line of the form
=local:user:uid:gid:homedir:dash:ext:
Here local is an address; user, uid, and gid are the account name, uid, and gid of the user in charge of local; and messages to local will
be controlled by homedir/.qmaildashext.
If there are several assignments for the same local address, qmail-lspawn will use the first one.
local is interpreted without regard to case.
WILDCARD ASSIGNMENTS
A wildcard assignment is a line of the form
+loc:user:uid:gid:homedir:dash:pre:
This assignment applies to any address beginning with loc, including loc itself. It means the same as
=locext:user:uid:gid:homedir:dash:preext:
for every string ext.
A more specific wildcard assignment overrides a less specific assignment, and a simple assignment overrides any wildcard assignment. For
example:
+:alias:7790:2108:/var/lib/qmail/alias:-::
+joe-:joe:507:100:/home/joe:-::
=joe:joe:507:100:/home/joe:::
The address joe is handled by the third line; the address joe-direct is handled by the second line; the address bill is handled by the
first line.
SEE ALSO
qmail-pw2u(8), qmail-newu(8), qmail-lspawn(8)
qmail-users(5)