I've been trying to set up NTP authentication between a server and a workstation. Both point to the same NTP server which is on a different physical box with its own IP address. I followed the steps below but I get the following result. How can I get this working?
Expected (on workstation):
Result:
Last edited by Scott; 10-30-2013 at 02:18 PM..
Reason: Added code tags
All,
How do you set a Solaris 9 server which received ntp updates from a ntp server to broadcast them on a local subnet. I have created a /etc/inet/ntp.conf file to receive the updates from a server on network and need to make this server become like a ntp relay from the main server.
Any... (1 Reply)
Greetings!
I just managed to install Solaris 10 on a Sparc based machine. However, there might be a problem with the way ssh is configured.
I CAN ssh from the machine into another on the network (same subnet, as root), but then the newly installed machine CANNOT seem to accept incoming ssh... (2 Replies)
Hi,
I have gone through various sites describing on how to setup NTP and also troubleshooting. Even then, I have problems. It is described as under:
My NTP server is running on Windows 2003. It is also a PDC. It gets its time through a GPS based solution. While all my workstations running on XP... (10 Replies)
This is a zone running Solaris 10u8 on a 6320 blade. The global zone is also running 10u8.
One my users is attempting to change his password and getting a following screen:
$ ssh remotesys
Password:
Warning: Your password has expired, please change it now.
New Password:
Re-enter new... (1 Reply)
All here, thank you for listening. Now I've set up a Linux NTP server by adding a external windows NTP server in /etc/ntp.conf. Then I start the ntpd daemon. But how often does the Linux NTP server update its time with the external NTP server? I've looked up everywhere but found no information... (1 Reply)
Hi,
I have two ntp servers in my cluster and I want all the nodes in my cluster to sync with either of the ntp servers or just one. Unfortunately it keep rotating the sync, between my ntp server 1, ntp server 2 and local. Is there anyway I can change the sync to avoid local?
# ntpq -p
... (3 Replies)
Hi All
Appreciate your help.
Here is the scenario:
1. Five months back we configured md5 authentication with network devices and NTP server and it worked fine.
2.Last week all of a sudden the network devices are out of sync.
3.We changed the md5 key and it started working.
... (0 Replies)
Discussion started by: iqtan
0 Replies
LEARN ABOUT SUSE
ntptrace
ntptrace(1) General Commands Manual ntptrace(1)NAME
ntptrace - trace a chain of NTP servers back to the primary source
SYNOPSIS
ntptrace [ -vdn ] [ -r retries ] [ -t timeout ] [ server ]
DESCRIPTION
ntptrace determines where a given Network Time Protocol (NTP) server gets its time from, and follows the chain of NTP servers back to
their master time source. If given no arguments, it starts with localhost . Here is an example of the output from ntptrace :
% ntptrace localhost: stratum 4, offset 0.0019529, synch distance 0.144135 server2ozo.com: stratum 2, offset 0.0124263, synch distance
0.115784 usndh.edu: stratum 1, offset 0.0019298, synch distance 0.011993, refid On each line, the fields are (left to right): the host
name, the host stratum, the time offset between that host and the local host (as measured by ntptrace ; this is why it is not always zero
for " localhost "), the host synchronization distance, and (only for stratum-1 servers) the reference clock ID. All times are given in sec-
onds. Note that the stratum is the server hop count to the primary source, while the synchronization distance is the estimated error rela-
tive to the primary source. These terms are precisely defined in RFC-1305.
OPTIONS -d Turns on some debugging output.
-n Turns off the printing of host names; instead, host IP addresses are given. This may be useful if a nameserver is down.
-r retries Sets the number of retransmission attempts for each host (default = 5).
-t timeout Sets the retransmission timeout (in seconds) (default = 2).
-v Prints verbose information about the NTP servers.
BUGS
This program makes no attempt to improve accuracy by doing multiple samples.
SEE ALSO
More documentation is available in the package ntp-doc.
AUTHOR
David L. Mills <mills@udel.edu>
ntp 4.1.1b-r5ntptrace(1)