Using the data and framework in the previous posts (14M lines, about 1 GB), I get:
not 50000 as desired.
The timing was:
The number of lines in the result varied, of 4 times, it did get 50000 once, the other 3 were 27K, 29K, and 30K, all of the latter with the ioctl message.
This is just for this 3GB workstation, a single datapoint.
Best wishes ... cheers, drl
Last edited by drl; 11-02-2013 at 02:27 PM..
Reason: Minor typo.
Hi,
There seems to some hack attempts in my site. I have attached the index page of my site and I need to remove the below lines from the index page. The below lines are at the center of the file.
-->
</style>
<script>E V A L( unescape(... (5 Replies)
All,
I have a text file with several entries like below:
personname
personname.domain.com
I know there is a way to use vi to remove only the personname.domain.com line. Can someone help? I believe that it involves /s/g/ something...I just can't remember the exact syntax.
Thanks (2 Replies)
Hi gurus,
i'm trying to remove a number of lines from a large file using the following command:
sed '1,5000d' oldfile > newfile
Somehow the lines in the old file are not deleted...
Am I doing this wrongly? Any suggestions? :confused:
Thanks! :)
wee (10 Replies)
A small question
I have a test.txt file
I have contents as:
a:google
b:yahoo
:
c:facebook
:
d:hotmail
How do I remove the line with :
my output should be
a:google
b:yahoo
c:facebook
d:hotmail (5 Replies)
Hi,
I'm not a expert in shell programming, so i've come here to take help from u gurus.
I'm trying to tailor a csv file that i got to make it work for the LOAD FROM command.
I've a datatable csv of the below format -
--in file format
xx,xx,xx ,xx , , , , ,,xx,
xxxx,, ,, xxx,... (11 Replies)
Hey Gang-
I have a list of servers. I want to exclude servers that begin with and end with certain characters. Is there an easy command to do this?
Example
wvm1234dev
wvm1234pro
uvm1122dev
uvm1122bku
uvm1344dev
I want to exclude any lines that start with "wvm" OR "uvm" AND end... (7 Replies)
I have two files, a keepout.txt and a database.csv. They're unsorted, but could be sorted.
keepout:
user1
buser3
anuser19
notheruser27
database:
user1,2343,"information about",field,blah,34
user2,4231,"mo info",etc,stuff,43
notheruser27,4344,"hiya",thing,more thing,423... (4 Replies)
Hello everyone,
Although it seems easy, I've been stuck with this problem for a moment now and I can't figure out a way to get it done.
My problem is the following:
I have a file where each line is a sequence of IP addresses, example :
10.0.0.1 10.0.0.2
10.0.0.5 10.0.0.1 10.0.0.2... (5 Replies)
I have been searching and trying to come up with an awk that will perform the following on a
converted text file (original is a pdf).
1. Since the first two lines are (begin with) text they are removed
2. if $1 is a number then all text is merged (combined) into one line until the next... (3 Replies)
Discussion started by: cmccabe
3 Replies
LEARN ABOUT LINUX
irsend
IRSEND(1) User Commands IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.9.0-pre1 October 2010 IRSEND(1)