10-28-2013
What Linux distribution and version? Is your version of GRUB GRUB2 or Legacy GRUB?
6 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Hi people,I am trying to install Debian Lenny Betta-2 on a system that has the built in promise chip for "Raid 0" but when I finished the install and then I reboot ,I get "grub loading,pleas wate... Error 2.
also the Debian Lenny Betta-2 is identifying both drives ,instead of a singular drive... (4 Replies)
Discussion started by: thegreatalsky
4 Replies
2. Red Hat
All
I am trying to get RHEL 5.4 to load to the XEN enabled kernel but I am not having much luck. My grub.conf looks like it has 2.6.18-194.11.3.el5xen as the 1st one but when I do a uname -a I get the NON xen enabled kernel. I know I am doing something stupid but if anybody has any... (1 Reply)
Discussion started by: razor3928
1 Replies
3. Solaris
Hi,
I`m on SunFire480R with Solaris 10. Disk in rootdg group failed, so it was replaced. However, I cannot make Veritas initalise the replaced disk:
# vxdctl enable
# vxdisk list c1t0d0s2
Device: c1t0d0s2
devicetag: c1t0d0
type: auto
flags: online error private autoconfig... (1 Reply)
Discussion started by: masloff
1 Replies
4. Solaris
I changed disk controller. Unplugged every disk, inserted another controller card, an IBM M1015. The disks are recognized in BIOS, and the controller card's BIOS shows up. But after that, I drop into GRUB and a prompt. That is all.
How shall I solve this problem? I am thinking of booting from... (2 Replies)
Discussion started by: kebabbert
2 Replies
5. Ubuntu
Hi,
a little while ago, one of the GPT Partitioned hard disk had gone faulty in a Mirror RAID and is now successfully replaced.
here is how I did that.
1) created identical partition table on the new disk.
2) attached the mirrors using md commands.
The whole procedure is given... (5 Replies)
Discussion started by: busyboy
5 Replies
6. AIX
OSLevel: 5300-10-02-0943
System Model: IBM,8203-E4A
Power 6
==
Hi!
I replaced a failed pdisk in the raid enclosure as follows,
- rmdev -l 'pdisk18' '-d'
- Replaced it.
- cfgmgr (detected)
- I can see the new drive, with the correct serial #
lscfg -v -l pdisk18
pdisk18... (2 Replies)
Discussion started by: estrar
2 Replies
LEARN ABOUT LINUX
grub-probe
GRUB-PROBE(8) System Administration Utilities GRUB-PROBE(8)
NAME
grub-probe - probe device information for GRUB
SYNOPSIS
grub-probe [OPTION]... [PATH|DEVICE]
DESCRIPTION
Probe device information for a given path (or device, if the -d option is given).
-d, --device
given argument is a system device, not a path
-m, --device-map=FILE
use FILE as the device map [default=/boot/grub/device.map]
-t, --target=(fs|fs_uuid|fs_label|drive|device|partmap|abstraction)
print filesystem module, GRUB drive, system device, partition map module or abstraction module [default=fs]
-h, --help
display this message and exit
-V, --version
print version information and exit
-v, --verbose
print verbose messages
REPORTING BUGS
Report bugs to <bug-grub@gnu.org>.
SEE ALSO
grub-fstest(1)
The full documentation for grub-probe is maintained as a Texinfo manual. If the info and grub-probe programs are properly installed at
your site, the command
info grub-probe
should give you access to the complete manual.
grub-probe (GRUB) 1.99-12ubuntu5 October 2011 GRUB-PROBE(8)