Grub not loading from replaced disk Post: 302868663

6 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

grub loading stage 1.5.

Hi people,I am trying to install Debian Lenny Betta-2 on a system that has the built in promise chip for "Raid 0" but when I finished the install and then I reboot ,I get "grub loading,pleas wate... Error 2. also the Debian Lenny Betta-2 is identifying both drives ,instead of a singular drive...

2. Red Hat

Grub is not loading the correct kernel

All I am trying to get RHEL 5.4 to load to the XEN enabled kernel but I am not having much luck. My grub.conf looks like it has 2.6.18-194.11.3.el5xen as the 1st one but when I do a uname -a I get the NON xen enabled kernel. I know I am doing something stupid but if anybody has any...

3. Solaris

Veritas not attaching replaced disk

Hi, I`m on SunFire480R with Solaris 10. Disk in rootdg group failed, so it was replaced. However, I cannot make Veritas initalise the replaced disk: # vxdctl enable # vxdisk list c1t0d0s2 Device: c1t0d0s2 devicetag: c1t0d0 type: auto flags: online error private autoconfig...

4. Solaris

Changed disk controller -> drops into GRUB?!

I changed disk controller. Unplugged every disk, inserted another controller card, an IBM M1015. The disks are recognized in BIOS, and the controller card's BIOS shows up. But after that, I drop into GRUB and a prompt. That is all. How shall I solve this problem? I am thinking of booting from...

5. Ubuntu

Linux LVM.. Grub not loading from replaced disk

Hi, a little while ago, one of the GPT Partitioned hard disk had gone faulty in a Mirror RAID and is now successfully replaced. here is how I did that. 1) created identical partition table on the new disk. 2) attached the mirrors using md commands. The whole procedure is given...

6. AIX

Replaced pdisk not showing up in SAS Disk Array Configuration

OSLevel: 5300-10-02-0943 System Model: IBM,8203-E4A Power 6 == Hi! I replaced a failed pdisk in the raid enclosure as follows, - rmdev -l 'pdisk18' '-d' - Replaced it. - cfgmgr (detected) - I can see the new drive, with the correct serial # lscfg -v -l pdisk18 pdisk18...

LEARN ABOUT LINUX

grub-probe

GRUB-PROBE(8)						  System Administration Utilities					     GRUB-PROBE(8)

NAME

       grub-probe - probe device information for GRUB

SYNOPSIS

       grub-probe [OPTION]... [PATH|DEVICE]

DESCRIPTION

       Probe device information for a given path (or device, if the -d option is given).

       -d, --device
	      given argument is a system device, not a path

       -m, --device-map=FILE
	      use FILE as the device map [default=/boot/grub/device.map]

       -t, --target=(fs|fs_uuid|fs_label|drive|device|partmap|abstraction)
	      print filesystem module, GRUB drive, system device, partition map module or abstraction module [default=fs]

       -h, --help
	      display this message and exit

       -V, --version
	      print version information and exit

       -v, --verbose
	      print verbose messages

REPORTING BUGS

       Report bugs to <bug-grub@gnu.org>.

SEE ALSO

       grub-fstest(1)

       The  full  documentation  for  grub-probe is maintained as a Texinfo manual.  If the info and grub-probe programs are properly installed at
       your site, the command

	      info grub-probe

       should give you access to the complete manual.

grub-probe (GRUB) 1.99-12ubuntu5				   October 2011 						     GRUB-PROBE(8)