-bash-3.00$ /usr/local/bin/sudo /usr/sbin/cfgadm -la
Ap_Id Type Receptacle Occupant Condition
c0 scsi-bus connected configured unknown
c0::dsk/c0t0d0 CD-ROM connected configured unknown
c1 scsi-bus connected configured unknown
c1::dsk/c1t0d0 disk connected configured unknown
c1::dsk/c1t1d0 disk connected configured unknown
c2 scsi-bus connected unconfigured unknown
usb0/1 unknown empty unconfigured ok
usb0/2 unknown empty unconfigured ok
-bash-3.00$
- cfgadm -c unconfigure c1::dsk/c1t0d0
2 .Verify that the device is now unconfigured.
-bash-3.00$ /usr/local/bin/sudo /usr/sbin/cfgadm -la
3. Confirm that the hard drive you want to remove from the server
is no longer visible to the operating system.
- /usr/local/bin/sudo /usr/sbin/format
4. The drive blue LED should now be lit
5. Open front bezel on the server.
6. Slide the catch to the right, remove the drive <<<<-- REMOVE FAILED DISK
7. Slide the catch to the right, install the new drive. <<<<-- INSERT NEW DISK
8. Push the metal level until the HDD clicks in place.
9. Close the front bezel.
10. Configure the newly installed hard drive e.g.
- cfgadm -la
- cfgadm -c configure c1::dsk/c1t0d0
I have removed the failed disk and inserted the new disk.
However I am unable to configure the disk getting below error:-
Code:
-bash-3.00$ /usr/local/bin/sudo /usr/sbin/cfgadm -c configure c1::dsk/c1t0d0
cfgadm: Hardware specific failure: failed to configure SCSI device: No such device or address
-bash-3.00$
This is what my cfgadm -al output shows:-
Code:
-bash-3.00$ /usr/local/bin/sudo /usr/sbin/cfgadm -la
Ap_Id Type Receptacle Occupant Condition
c0 scsi-bus connected configured unknown
c0::dsk/c0t0d0 CD-ROM connected configured unknown
c1 scsi-bus connected configured unknown
c1::dsk/c1t0d0 disk connected unconfigured unknown
c1::dsk/c1t1d0 disk connected configured unknown
c2 scsi-bus connected unconfigured unknown
usb0/1 unknown empty unconfigured ok
usb0/2 unknown empty unconfigured ok
-bash-3.00$
This is what my format command showing:-
Code:
-bash-3.00$ /usr/local/bin/sudo /usr/sbin/format
Password:
Searching for disks...done
AVAILABLE DISK SELECTIONS:
0. c1t1d0 <SUN72G cyl 14087 alt 2 hd 24 sec 424> ROOTMIRR
/pci@1c,600000/scsi@2/sd@1,0
Specify disk (enter its number):
is it safe to run this command on Server -->>>>
Code:
devfsadm –C –c disks
will it make my new inserted disk visible on system?
Please advise.
Thanks a lot.
Last edited by manalisharmabe; 10-24-2013 at 01:02 PM..
Hi Experts,
I have configured A D40 Array. There is an faulty disk which is not part of an raid volume but shows fault in the diagnostics.
pdisk15 U0.1-P1-I1/Q1-W40AA83CC2400D
SSA160 Physical Disk Drive ( MB)
Is there a way to stop this... (2 Replies)
Hi all,
I guess most of you have seen this error message while installing Solaris 10 on an x86 platform. I got the error message while installing from DVD ISO on my home VMWare ESXi server.
It took me a long time to figure the exact issue and a subsequent solution. the solution is very... (1 Reply)
Hi folk,
I have this hardware faunty message, but dont know which hardware is this ? can you guide me ?
--------------- ------------------------------------ -------------- ---------
TIME EVENT-ID MSG-ID SEVERITY
---------------... (9 Replies)
Hi,
Recently i came across a disk that seems to be faulty and need help. I have gathered some information by running below commands and any help on how to solve this will be great.
# uname –a
SunOS XYZ 5.7 Generic_106541-16 sun4u sparc SUNW,Ultra-4
#df -k
Filesystem kbytes used... (3 Replies)
Requirement to remove a faulty mirrored disk from hp-ux LVM
<root@pdwp1s>/etc # vgdisplay -v /dev/vg00
vgdisplay: Warning: couldn't query physical volume "/dev/dsk/c2t0d0":
The specified path does not correspond to physical volume attached to
this volume group
vgdisplay: Warning: couldn't... (9 Replies)
Hi,
Have mirrored the primary disk to 3 .
Server and OS:
# uname -a
HP-UX pdwp1s B.11.11 U 9000/800 118434630 unlimited-user license
# model
9000/800/L3000-7x
# strings /etc/lvmtab
/dev/vg00
+F@<
/dev/dsk/c1t2d0
/dev/dsk/c2t2d0
/dev/dsk/c2t0d0
But now I have only 1 disk... (5 Replies)
Hello,
I'm new to this forum and as you will see from my question I'm new to UNIX as well.
One of our costumers has HP rx4640 running on UNIX with two 300GB hot-swappable disks that are mirrored. They reported to us that one of the disks is faulty and they want us to take care of it. Below is... (16 Replies)
Hi,
I'm trying to generate an alert related to Power Supply Failure.
As its difficult to generate such an event, Is it possible to set the status of a Power Supply Unit as "Faulty"
Any ideas are welcome and highly appreciated
-Thanks (3 Replies)
Hi,
Again a question about virt-install.
Someone knows how to add hardware in the virt-install command?
I put the first disk with --disks path=/.... but I need a second disk and I don't know how to include it?
Thanks (2 Replies)
I plugged both power cables in both power supply. When I unplugged each power cable one by one, the SPARC T4-1 machine keep running. However, show faulty command shows below message. (I have also attached the picture of both power supply)
-> show faulty
Target ... (1 Reply)