Login or Register to Ask a Question and Join Our Community

Sponsored Content
Full Discussion: Eth0 not running in redhat 6.4
Operating Systems Linux Red Hat Eth0 not running in redhat 6.4 Post 302867273 by cjashu on Wednesday 23rd of October 2013 05:50:56 PM
Old 10-23-2013
Hello Verdepollo,

thank you so much for your reply. I really appreciate it. Actually, during the initial installation, the eth0 could not be configured at all. I assigned the ip,dg,mask during the installation. The Network Manager could not activate the eth0 interface. This is the exact message I got " Failed to activate these network interfaces: eth0"

The second interface is not even showing up.

Thank you again.
Arrey
 

10 More Discussions You Might Find Interesting

1. IP Networking

Linux eth0 incative

Hi there, I got a problem with my linux eth0. It worked well, just one day when i boot it, "Failed" to be active. The eth0 is inactive! I tried to use KDE network configuration tool to add the type of the eth card, I can't make it active. It gave me warning of "the eth card can't be... (1 Reply)
Discussion started by: gusla
1 Replies

2. IP Networking

Adding an IP to eth0

Hi there guys! I have a small task that I have to accomplish, but I don't seem to be able to do that. I have a server that I don't have physical access to, and I mostly control it with webmin. The server is running 2 websites. Both of these websites have their own domains that are linked to... (1 Reply)
Discussion started by: D-Lexy
1 Replies

3. UNIX for Dummies Questions & Answers

How to check both the processores running or not in redhat linux

Hi, We have dual processor dell machine loaded with redhat linux 7.2. It was working fine without any problem but recently power went off so suddenly system switched off. From then onwards system is running very slow. My suspect is on processor. How to check both the processors running properly or... (8 Replies)
Discussion started by: bache_gowda
8 Replies

4. Ubuntu

Trying to config eth0 - Ubuntu

Greetings, I have installed a Ubuntu server and attempting put a static IP address on interface ETH0. I edited the /etc/network/interfaces with the following: auto eth0 iface eth0 inet static address 192.168.203.270 gateway 192.168.203.1 netwask 255.255.255.0 network 192.168.0.0... (2 Replies)
Discussion started by: jroberson
2 Replies

5. Red Hat

Problems running redhat config samba in the GUI

hi Recently the above option has stopped working all together. On clicking on this option it appears as though the window will open as the outline of the box appears but nothing more. On running this from a command prompt within the GUI , I get the following error: The last line... (0 Replies)
Discussion started by: timcs
0 Replies

6. UNIX for Dummies Questions & Answers

how can I find which one is eth0?

Hi, Just installed Centos 5.1 on HP DL360, on this system I have to close to ten nic's. How can I find which one is eth0? When I do " ifconfig -a" I see all of them, but I can't tell which is eth0? Please advice. (2 Replies)
Discussion started by: samnyc
2 Replies

7. Red Hat

redhat 5.2 tikanga crond running but not reading crontab file

Issue:crond is running, can even restart it and /var/log/cron shows it starting. The /etc/crontab file is correct as compared to another machine. I set the crontab file to enter a datestamp into a file under /tmp every minute. Thing is, the crontab file is not being read or cron is not working... (12 Replies)
Discussion started by: robjmarquez
12 Replies

8. Red Hat

Eth0 Limitations

Hi, I have noticed some performance issues on my RHEL5 server but the memory and CPU utilization on the box is fine. I have a 1G full duplexed eth0 card and I am suspicious that this may be causing the problem. My eth0 settings are as follows: Settings for eth0: Supported ports: ... (12 Replies)
Discussion started by: Duffs22
12 Replies

9. Red Hat

Not showing ifcfg eth0....redhat enterprise Linux 6.2

Hello, I'm using dell inspiron 14R laptop and I installed Redhat enterprise 6.2 on this. After successfully installation i did not found any network interface on this. when i'm trying to load/add qeth driver . The driver is not found showing this message. Bash: lsmod | grep qeth Bash:... (4 Replies)
Discussion started by: dearsumon
4 Replies

10. IP Networking

iptables On for eth0 and off for other interfaces

Hi all, I am running a CentOS 6.4 box as an IDS and I need to configure one interface as the management interface which will require a firewall. However other ports (in promisc mode without IP) will have to be configured such that IPtables allows all traffic. I need to achieve this by editing... (4 Replies)
Discussion started by: landossa
4 Replies

LEARN ABOUT SUSE

ifcfg-wireless

IFCFG(5)						       Network configuration							  IFCFG(5)

NAME

       ifcfg-wireless - wireless LAN network interface configuration

SYNOPSIS

       /etc/sysconfig/network/ifcfg-wlan-*
       /etc/sysconfig/network/ifcfg-type-wlan

GENERAL

       Wireless  networks  need  some additional configuration data compared to ethernet ones. Therefore additional variables for ifcfg files were
       introduced.  All wireless LAN specific variables are described in the ifcfg template file /etc/sysconfig/network/ifcfg.template. It is pos-
       sible to configure more than one wireless network accepted for association. To achieve this add suffix _1 to all wireless variables for the
       second network, _2 for the this, and so on. Example: WIRELESS_ESSID_1="second_net" You can have up to  ten  wireless  networks  configured.
       Some  wireless  variables  are not applicable to a single wireless network but are global to the interface. The description of the variable
       points this out.

BUGS

       Please report bugs at <http://www.suse.de/feedback>

AUTHOR

       Christian Zoz <zoz@suse.de> -- ifup script
       Michal Svec <msvec@suse.cz> -- ifup script
       Bjoern Jacke -- ifup script
       Mads Martin Joergensen <mmj@suse.de> -- ifup manual page
       Michal Ludvig <mludvig@suse.cz> -- tunnel support
       Joachim Gleissner <jg@suse.de> -- wireless support

SEE ALSO

       ifup(8).

sysconfig							   December 2005							  IFCFG(5)
All times are GMT -4. The time now is 02:12 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy