10-23-2013
Hello Verdepollo,
thank you so much for your reply. I really appreciate it. Actually, during the initial installation, the eth0 could not be configured at all. I assigned the ip,dg,mask during the installation. The Network Manager could not activate the eth0 interface. This is the exact message I got " Failed to activate these network interfaces: eth0"
The second interface is not even showing up.
Thank you again.
Arrey
10 More Discussions You Might Find Interesting
1. IP Networking
Hi there,
I got a problem with my linux eth0.
It worked well, just one day when i boot it, "Failed" to be active.
The eth0 is inactive! I tried to use KDE network configuration tool to add the type of the eth card, I can't make it active. It gave me warning of "the eth card can't be... (1 Reply)
Discussion started by: gusla
1 Replies
2. IP Networking
Hi there guys!
I have a small task that I have to accomplish, but I don't seem to be able to do that.
I have a server that I don't have physical access to, and I mostly control it with webmin. The server is running 2 websites. Both of these websites have their own domains that are linked to... (1 Reply)
Discussion started by: D-Lexy
1 Replies
3. UNIX for Dummies Questions & Answers
Hi,
We have dual processor dell machine loaded with redhat linux 7.2. It was working fine without any problem but recently power went off so suddenly system switched off. From then onwards system is running very slow. My suspect is on processor. How to check both the processors running properly or... (8 Replies)
Discussion started by: bache_gowda
8 Replies
4. Ubuntu
Greetings,
I have installed a Ubuntu server and attempting put a static IP address on interface ETH0. I edited the /etc/network/interfaces with the following:
auto eth0
iface eth0 inet static
address 192.168.203.270
gateway 192.168.203.1
netwask 255.255.255.0
network 192.168.0.0... (2 Replies)
Discussion started by: jroberson
2 Replies
5. Red Hat
hi
Recently the above option has stopped working all together. On clicking on this option it appears as though the window will open as the outline of the box appears but nothing more.
On running this from a command prompt within the GUI , I get the following error:
The last line... (0 Replies)
Discussion started by: timcs
0 Replies
6. UNIX for Dummies Questions & Answers
Hi,
Just installed Centos 5.1 on HP DL360, on this system I have to close to ten nic's. How can I find which one is eth0? When I do " ifconfig -a" I see all of them, but I can't tell which is eth0?
Please advice. (2 Replies)
Discussion started by: samnyc
2 Replies
7. Red Hat
Issue:crond is running, can even restart it and /var/log/cron shows it starting. The /etc/crontab file is correct as compared to another machine. I set the crontab file to enter a datestamp into a file under /tmp every minute. Thing is, the crontab file is not being read or cron is not working... (12 Replies)
Discussion started by: robjmarquez
12 Replies
8. Red Hat
Hi,
I have noticed some performance issues on my RHEL5 server but the memory and CPU utilization on the box is fine.
I have a 1G full duplexed eth0 card and I am suspicious that this may be causing the problem. My eth0 settings are as follows:
Settings for eth0:
Supported ports: ... (12 Replies)
Discussion started by: Duffs22
12 Replies
9. Red Hat
Hello, I'm using dell inspiron 14R laptop and I installed Redhat enterprise 6.2 on this. After successfully installation i did not found any network interface on this.
when i'm trying to load/add qeth driver . The driver is not found showing this message.
Bash: lsmod | grep qeth
Bash:... (4 Replies)
Discussion started by: dearsumon
4 Replies
10. IP Networking
Hi all,
I am running a CentOS 6.4 box as an IDS and I need to configure one interface as the management interface which will require a firewall. However other ports (in promisc mode without IP) will have to be configured such that IPtables allows all traffic.
I need to achieve this by editing... (4 Replies)
Discussion started by: landossa
4 Replies
LEARN ABOUT MOJAVE
tc-mirred
Mirror/redirect action in tc(8) Linux Mirror/redirect action in tc(8)
NAME
mirred - mirror/redirect action
SYNOPSIS
tc ... action mirred DIRECTION ACTION [ index INDEX ] dev DEVICENAME
DIRECTION := { ingress | egress }
ACTION := { mirror | redirect }
DESCRIPTION
The mirred action allows packet mirroring (copying) or redirecting (stealing) the packet it receives. Mirroring is what is sometimes
referred to as Switch Port Analyzer (SPAN) and is commonly used to analyze and/or debug flows.
OPTIONS
ingress
egress Specify the direction in which the packet shall appear on the destination interface.
mirror
redirect
Define whether the packet should be copied (mirror) or moved (redirect) to the destination interface.
index INDEX
Assign a unique ID to this action instead of letting the kernel choose one automatically. INDEX is a 32bit unsigned integer greater
than zero.
dev DEVICENAME
Specify the network interface to redirect or mirror to.
EXAMPLES
Limit ingress bandwidth on eth0 to 1mbit/s, redirect exceeding traffic to lo for debugging purposes:
# tc qdisc add dev eth0 handle ffff: ingress
# tc filter add dev eth0 parent ffff: u32
match u32 0 0
action police rate 1mbit burst 100k conform-exceed pipe
action mirred egress redirect dev lo
Mirror all incoming ICMP packets on eth0 to a dummy interface for examination with e.g. tcpdump:
# ip link add dummy0 type dummy
# ip link set dummy0 up
# tc qdisc add dev eth0 handle ffff: ingress
# tc filter add dev eth0 parent ffff: protocol ip
u32 match ip protocol 1 0xff
action mirred egress mirror dev dummy0
Using an ifb interface, it is possible to send ingress traffic through an instance of sfq:
# modprobe ifb
# ip link set ifb0 up
# tc qdisc add dev ifb0 root sfq
# tc qdisc add dev eth0 handle ffff: ingress
# tc filter add dev eth0 parent ffff: u32
match u32 0 0
action mirred egress redirect dev ifb0
SEE ALSO
tc(8), tc-u32(8)
iproute2 11 Jan 2015 Mirror/redirect action in tc(8)