10-21-2013
As others have said, apple vs. orange.
Both have their place. So while the argument has been on what PCIe can do vs USB, certainly USB has strengths for certain cases.
So.. the answer is "no", but iMHO, it's because one is an apple and the other is an orange.
If you think differently, go and get on of those high speed USB 3.0 docking solutions that do displaylink to handle multiple monitors over your USB 3.0... and when that fails (and eventually it will), you will have a better understanding for why this just doesn't work.
9 More Discussions You Might Find Interesting
1. BSD
Hi!
I just wanted to know what network cards are supported in FreeBSD. I have looked at the list of supported cards but I can't find any of them in the stores. Is the list not updated, I would really preciate info about where (in EU, Sweden) I can buy them.
/Peter (2 Replies)
Discussion started by: Barfly.se
2 Replies
2. Solaris
How do I get the PCI ID for my Realtek adapter?
It's a Solaris x86 installation. (5 Replies)
Discussion started by: kuultak
5 Replies
3. UNIX for Dummies Questions & Answers
Hi,
im having a problem installing my pci wireless card. Im using knoppix, but my problem is with the mobo i think. im using an older laptop, toshiba satellite 2540 and when i plug in the card i get lights on sometimes. this means its getting power right. so then to install the card into the... (0 Replies)
Discussion started by: jestra
0 Replies
4. UNIX for Dummies Questions & Answers
platform: sunblade 100
Solaris 10.
When running a test-all from the ok prompt on this new (to me) system, it locks up at pci@1f,0/usb/c,3. It's been there for about 25 minutes.
I do have a usb keyboard and mouse attached, both are known good. There is no flash stick/ thumb drive... (0 Replies)
Discussion started by: montana77
0 Replies
5. Linux
I installed PCI Card HP SC44Ge - SAS1068E
on my linux CentOS 5.4
is there a way to find out if the PCI is properly installed and recognized by linux.
lspci is enough?
just to add that PCI card is connected to a tape...
also how can I find out driver and firmware version?
thanks a... (1 Reply)
Discussion started by: karlochacon
1 Replies
6. UNIX for Dummies Questions & Answers
Is there an easy way to setup a cross-over cable (USB-USB) between a linux box and a windows PC? My 2 machines are next to each other but I really do not want to keep transfering my files using my USB drive.
Thanks! (4 Replies)
Discussion started by: Xterra
4 Replies
7. Programming
For a project that I'm working on I want to write a low level PCI driver, but I can't seem to find any free/cheap documentation on PCI firmware specifications. I came across the "pci firmware specification 3.0" manual but this costs USD $1000 :eek:. I am not developing a commercial product... (13 Replies)
Discussion started by: neur0n
13 Replies
8. Solaris
How do I find any available PCI slots on a v440?
When I run prtconf, I get the following output? But I am not able to make out whether all the PCI slots are used.
================================= IO Devices =================================
Bus Freq
Brd Type MHz Slot ... (1 Reply)
Discussion started by: jtamminen
1 Replies
9. Slackware
Need to free up a usb port for webcam. What does xorg.conf look like in order to work if I move mouse to PCI port via a converter plug? (1 Reply)
Discussion started by: slak0
1 Replies
LEARN ABOUT DEBIAN
oss_usb
oss_usb(7) OSS Devices oss_usb(7)
NAME
oss_usb - USB Audio/MIDI/Mixer driver
DESCRIPTION
The Open Sound System driver for USB Audio and MIDI devices.
AUDIO
The Audio driver supports:
o 8-96Khz Playback/Recording
o 8 or 16 or 32 bits
o 2, 4, 6 or 8 channel audio.
o SPDIF digital output and Input
o AC3 passthrough
o Volume control and device input mixer
MIDI
The oss_usb driver supports all MIDI devices that are compatible with the official USB MIDI specification. In addition the driver supports
few devices that use their own private protocol (including some Yamaha and Midiman models).
USB MIXER
The USB Audio mixer is a new type of mixer that doesn't have the normal volume controls found on AC97 or Legacy SB devices. The USB audio
mixer provides control for selecting the Alternate device setting - this usually allows the device to be switched into a Professional audio
mode (eg 24bit or 96Khz mode)
ALTERNATIVE SETTINGS
Some USB audio devices use a feature called as alternative settings for bandwidth management. Typically such devices have multiple high
speed inputs and outputs that may require more bandwidth than provided by the USB bus. The alternative settings feature is used to select
between multiple low speed devices or just few high speed devices.
When the device has multiple alternative settings an "altsetting" selector will be visible in the control panel for the device (use oss-
mix(1) or ossxmix(1) to change it). Alternative setting OFF means that all audio devices are disabled. The other settings provide different
combinations of high/medium speed devices. You can use the ossinfo(1) command (ossinfo -a -v3) to find out the devices supported by the
currently selected alternative settings and the capabilities of them.
KNOWN BUGS
Under Linux it is necessary to run the ossdetect -d and ossdevlinks commands after an USB device has been hot-plugged. Alternatively you
can execute soundoff and soundon to reload OSS.
OPTIONS
None
FILES
/etc/oss4/conf/oss_usb.conf Device configuration file
AUTHOR
4Front Technologies
16 December 2012 oss_usb(7)