10-21-2013
As others have said, apple vs. orange.
Both have their place. So while the argument has been on what PCIe can do vs USB, certainly USB has strengths for certain cases.
So.. the answer is "no", but iMHO, it's because one is an apple and the other is an orange.
If you think differently, go and get on of those high speed USB 3.0 docking solutions that do displaylink to handle multiple monitors over your USB 3.0... and when that fails (and eventually it will), you will have a better understanding for why this just doesn't work.
9 More Discussions You Might Find Interesting
1. BSD
Hi!
I just wanted to know what network cards are supported in FreeBSD. I have looked at the list of supported cards but I can't find any of them in the stores. Is the list not updated, I would really preciate info about where (in EU, Sweden) I can buy them.
/Peter (2 Replies)
Discussion started by: Barfly.se
2 Replies
2. Solaris
How do I get the PCI ID for my Realtek adapter?
It's a Solaris x86 installation. (5 Replies)
Discussion started by: kuultak
5 Replies
3. UNIX for Dummies Questions & Answers
Hi,
im having a problem installing my pci wireless card. Im using knoppix, but my problem is with the mobo i think. im using an older laptop, toshiba satellite 2540 and when i plug in the card i get lights on sometimes. this means its getting power right. so then to install the card into the... (0 Replies)
Discussion started by: jestra
0 Replies
4. UNIX for Dummies Questions & Answers
platform: sunblade 100
Solaris 10.
When running a test-all from the ok prompt on this new (to me) system, it locks up at pci@1f,0/usb/c,3. It's been there for about 25 minutes.
I do have a usb keyboard and mouse attached, both are known good. There is no flash stick/ thumb drive... (0 Replies)
Discussion started by: montana77
0 Replies
5. Linux
I installed PCI Card HP SC44Ge - SAS1068E
on my linux CentOS 5.4
is there a way to find out if the PCI is properly installed and recognized by linux.
lspci is enough?
just to add that PCI card is connected to a tape...
also how can I find out driver and firmware version?
thanks a... (1 Reply)
Discussion started by: karlochacon
1 Replies
6. UNIX for Dummies Questions & Answers
Is there an easy way to setup a cross-over cable (USB-USB) between a linux box and a windows PC? My 2 machines are next to each other but I really do not want to keep transfering my files using my USB drive.
Thanks! (4 Replies)
Discussion started by: Xterra
4 Replies
7. Programming
For a project that I'm working on I want to write a low level PCI driver, but I can't seem to find any free/cheap documentation on PCI firmware specifications. I came across the "pci firmware specification 3.0" manual but this costs USD $1000 :eek:. I am not developing a commercial product... (13 Replies)
Discussion started by: neur0n
13 Replies
8. Solaris
How do I find any available PCI slots on a v440?
When I run prtconf, I get the following output? But I am not able to make out whether all the PCI slots are used.
================================= IO Devices =================================
Bus Freq
Brd Type MHz Slot ... (1 Reply)
Discussion started by: jtamminen
1 Replies
9. Slackware
Need to free up a usb port for webcam. What does xorg.conf look like in order to work if I move mouse to PCI port via a converter plug? (1 Reply)
Discussion started by: slak0
1 Replies
LEARN ABOUT FREEBSD
usb_template
USB_TEMPLATE(4) BSD Kernel Interfaces Manual USB_TEMPLATE(4)
NAME
usb_template -- USB templates
SYNOPSIS
To compile this module into the kernel, place the following line in your kernel configuration file:
device usb_template
To load the module at boot time, place the following line in loader.conf(5):
usb_template_load="YES"
DESCRIPTION
The usb_template module implements various USB templates that are needed when programming an USB device side driver. A USB template consists
of an USB device descriptor, one or more USB configuration descriptors, one or more USB interface descriptors, one or more USB endpoint
descriptors, USB strings and additional USB descriptors. The USB template module currently has templates for USB Mass Storage, USB CDC Eth-
ernet and Message Transfer Protocol. USB templates are currently selected using the "hw.usb.template" sysctl. The "hw.usb.template" value
can be changed at any time, but will not have any effect until the USB device has been re-enumerated.
SEE ALSO
usb(4)
STANDARDS
The usb_template module complies to the USB 1.0, 2.0 and 3.0 standard.
HISTORY
The usb_template module was written by Hans Petter Selasky <hselasky@FreeBSD.org>.
BSD
March 18, 2014 BSD