I am running a number of processes through a kill -15 loop as a temporary fix to some viscious memory leaks. I cannot pass the entire list of processes through the kill at once, because the nature of the monitoring my client has will cause the software to failover.
Because of the large number of... (1 Reply)
I am in need of some help; think I have confused myself.
Here is the issue I am faced with.
The script log file was fine, the nohup.out file has tens of thousands of lines like illegal use of sleep: sleep seconds
So I assume there is something with the seconds calculation in the script... (1 Reply)
Hi All I have a requiremnt to run a script inside another script.
here i am pulling the record count from the table in oracle.If record count is greater than 0 the script is executed.The scripts updates the count in the table and again the count is found out and the condition is checked and same... (3 Replies)
Hi Forum
Im using sleep in a while loop goes around 10 times. i feed it a variable with the time i what it to sleep for eg sleep $sleepVal and then print system date and time to screen but sometimes 1 second is added to the time why is this
here my code
sleepVal=5
while
do
... (3 Replies)
Hi All,
i am very new to shall script . i am not that much aware of sleep command ,
i want to terminate the sleep command after certain time.
following is my code.
while
loop
sleep 1800
messag=/status.sql
donethe script will be on sleep untill the messag be comes P. here my requirement... (4 Replies)
Hello,
Need a little help with the script below. I can't get it to sleep :( I'm trying to get this to check if the process is running and if it is, wait 10 secs and check again. Keep doing this until it's not running and then stop checking and send the email.
#!/bin/ksh
mailto=`cat... (2 Replies)
I need help in script.
I want my one script execute every time at 6:30 am and i have no cron access.
So i am putting sleep command there , Script may took half an hour 35 min , it depend upon queries how much it take time, but that is not issue,
So i want according to stop time of... (15 Replies)
Discussion started by: pallvi_mahajan
15 Replies
LEARN ABOUT OSF1
sleep
sleep(1) General Commands Manual sleep(1)NAME
sleep - Suspends execution for at least the specified time
SYNOPSIS
sleep seconds
STANDARDS
Interfaces documented on this reference page conform to industry standards as follows:
sleep: XCU5.0
Refer to the standards(5) reference page for more information about industry standards and associated tags.
OPTIONS
None
OPERANDS
Non-negative integer specifying the number of seconds for which execution is to be suspended.
DESCRIPTION
The sleep command suspends execution of a process for at least the interval specified by seconds, which can range from 0 to 2,147,483,647
seconds. Depending on system activity, the actual time of suspension may be longer. See the sleep(3) reference page.
[Tru64 UNIX] seconds can be entered as a non-negative decimal, octal, or hexadecimal value.
NOTES
If sleep receives a SIGALARM signal before process execution has resumed, sleep takes one of the following actions: Terminates normally
with a 0 (zero) exit status. (See the sleep(3) reference page for more information.) Ignores the signal Performs default processing
EXIT STATUS
The following exit values are returned: Execution was successfully suspended for at least the requested time, or a SIGALARM signal was
received. An error occurred.
EXAMPLES
To display a message at 4-minute intervals for 20 minutes, create a shell script called remind containing the following:
for i do sleep 240; echo $i sleep 240; echo $i sleep 240; echo $i sleep 240; echo $i sleep 240; echo $i done
To display the message Try calling NHK at 4-minute intervals, enter: remind 'Try calling NHK' To run a command at regular intervals,
create a shell script containing the following:
while true do
date
sleep 60 done
This displays the date and time once a minute. To execute a command after a specified interval, enter the following; (sleep 3600;
echo Time's up) &
This displays the message "Time's up" after one hour.
ENVIRONMENT VARIABLES
The following environment variables affect the execution of sleep: Provides a default value for the internationalization variables that are
unset or null. If LANG is unset or null, the corresponding value from the default locale is used. If any of the internationalization vari-
ables contain an invalid setting, the utility behaves as if none of the variables had been defined. If set to a non-empty string value,
overrides the values of all the other internationalization variables. Determines the locale for the interpretation of sequences of bytes
of text data as characters (for example, single-byte as opposed to multibyte characters in arguments). Determines the locale for the for-
mat and contents of diagnostic messages written to standard error. Determines the location of message catalogues for the processing of
LC_MESSAGES.
SEE ALSO
Commands: wait(1)
Functions: alarm(3), pause(3), sigaction(2), sleep(3)
Standards: standards(5)sleep(1)