Hi,
I have the situaiton in which primary boot disk has bad sectors in Solaris 9. The other hard disk is mirrored using Solstice DiskSuite 4.2. I can reboot system with the other disk. My question is, when I replaced the boot disk with a new one, how can I create meta db and finally make it... (2 Replies)
What is the correct mkfs syntax to create mirrored disk files systems? I need to make the file system 20gb. For example:
machine# mkfs -F ufs /dev/md/dsk/d40
size not specified
ufs usage: mkfs special size(sectors) \
-m : dump fs cmd line used to make this partition
-V : print this... (4 Replies)
Hi all,
I have a V490 running with Solaris 10. The OS disk was mirrored. I wanted to break the mirror, boot with the secondary mirror, and re-mirror the OS with a new disk.
This is what I did,
detached the metadevices of the secondary mirror disk (disk 1)
metaclear-ed the metadevices,... (1 Reply)
Hello once again seeking your help,
I have a mirrored disk and need to unmirror it to mount it as a new file system (/export) but could not find the correct steps to do it with out affecting the original disk.
can anybody point me out on how to get this done.
Thanks!! (3 Replies)
I have a HP proliant ML 570 G3 with two 146GB disk drives mirrored(RAID1+0)
windows server 2003 was installed on that disk.
I will add a disk.(scsi 300GB)
I will install Linux on that additional disk.
I want to create multiple-boot system.
Is it possible?
I wanna know how to create... (0 Replies)
So I have mirrored disk already set up from c1t0d0 to c1t1d0. Is there some special procedures that I need to do before I do and then try to boot from the mirrored disk? I am using a V490 if that helps... (7 Replies)
Hi guys,
thanks for helping out.
If you have two boot disk mirrored and your primary boot disk fails, how will you boot the system from the second disk?
Thank you very much for your assistance on this matter.
Arrey (5 Replies)
Hi,
I'm looking to copy a boot disk on an old Solaris 8 system using dd. I'll bring the system down to single user mode and begin from there. I'm copying my source disk to a larger target disk. Do I need to do anything other than the 'dd' command below because the target disk is bigger? ... (2 Replies)
Discussion started by: sparcman
2 Replies
LEARN ABOUT MOJAVE
locale::codes::langvar
Locale::Codes::LangVar(3pm) Perl Programmers Reference Guide Locale::Codes::LangVar(3pm)NAME
Locale::Codes::LangVar - standard codes for language variation identification
SYNOPSIS
use Locale::Codes::LangVar;
$lvar = code2langvar('acm'); # $lvar gets 'Mesopotamian Arabic'
$code = langvar2code('Mesopotamian Arabic'); # $code gets 'acm'
@codes = all_langvar_codes();
@names = all_langvar_names();
DESCRIPTION
The "Locale::Codes::LangVar" module provides access to standard codes used for identifying language variations, such as those as defined in
the IANA language registry.
Most of the routines take an optional additional argument which specifies the code set to use. If not specified, the default IANA language
registry codes will be used.
SUPPORTED CODE SETS
There are several different code sets you can use for identifying language variations. A code set may be specified using either a name, or
a constant that is automatically exported by this module.
For example, the two are equivalent:
$lvar = code2langvar('en','alpha-2');
$lvar = code2langvar('en',LOCALE_CODE_ALPHA_2);
The codesets currently supported are:
alpha
This is the set of alphanumeric codes from the IANA language registry, such as 'arevela' for Eastern Armenian.
This code set is identified with the symbol "LOCALE_LANGVAR_ALPHA".
This is the default code set.
ROUTINES
code2langvar ( CODE [,CODESET] )
langvar2code ( NAME [,CODESET] )
langvar_code2code ( CODE ,CODESET ,CODESET2 )
all_langvar_codes ( [CODESET] )
all_langvar_names ( [CODESET] )
Locale::Codes::LangVar::rename_langvar ( CODE ,NEW_NAME [,CODESET] )
Locale::Codes::LangVar::add_langvar ( CODE ,NAME [,CODESET] )
Locale::Codes::LangVar::delete_langvar ( CODE [,CODESET] )
Locale::Codes::LangVar::add_langvar_alias ( NAME ,NEW_NAME )
Locale::Codes::LangVar::delete_langvar_alias ( NAME )
Locale::Codes::LangVar::rename_langvar_code ( CODE ,NEW_CODE [,CODESET] )
Locale::Codes::LangVar::add_langvar_code_alias ( CODE ,NEW_CODE [,CODESET] )
Locale::Codes::LangVar::delete_langvar_code_alias ( CODE [,CODESET] )
These routines are all documented in the Locale::Codes::API man page.
SEE ALSO
Locale::Codes
The Locale-Codes distribution.
Locale::Codes::API
The list of functions supported by this module.
http://www.iana.org/assignments/language-subtag-registry
The IANA language subtag registry.
AUTHOR
See Locale::Codes for full author history.
Currently maintained by Sullivan Beck (sbeck@cpan.org).
COPYRIGHT
Copyright (c) 2011-2013 Sullivan Beck
This module is free software; you can redistribute it and/or modify it under the same terms as Perl itself.
perl v5.18.2 2014-01-06 Locale::Codes::LangVar(3pm)