10-11-2013
Hi,
i have created a Grub Partition on the disk drive as it recommended in a
Guide
I have two 3 TB disks with mirroring. Is there anything related to creating the disk replication and then attaching it or something else?
Regards,
NMR
10 More Discussions You Might Find Interesting
1. HP-UX
Hi dear(s)
Can u explain how to add a disk through lvm with commands.
I need to add a 9 gb scsi HS disk to a Hp D class 9000 server. (2 Replies)
Discussion started by: sreekumar.R
2 Replies
2. UNIX for Dummies Questions & Answers
I'm setting-up my new computer, and would like to try out and switch between several OS (mostly different Linux distros). As I prefer to use separate partition for various dirs (/, home, usr, var, opt and perhaps local), I've come to the conclution that I'll run-out of partitions too soon, so I've... (1 Reply)
Discussion started by: koppe
1 Replies
3. UNIX for Advanced & Expert Users
Hi people,I am trying to install Debian Lenny Betta-2 on a system that has the built in promise chip for "Raid 0" but when I finished the install and then I reboot ,I get "grub loading,pleas wate... Error 2.
also the Debian Lenny Betta-2 is identifying both drives ,instead of a singular drive... (4 Replies)
Discussion started by: thegreatalsky
4 Replies
4. AIX
We have a filesystem which contains 8 hard disks but i am facing disk I/O issue becuase data is not spreading across all the disks.Is there any way i can check how data is spreading and any parameter we need to change to spread ata across all disks.
OS--AIX 5.3 (1 Reply)
Discussion started by: ukatru
1 Replies
5. Red Hat
All
I am trying to get RHEL 5.4 to load to the XEN enabled kernel but I am not having much luck. My grub.conf looks like it has 2.6.18-194.11.3.el5xen as the 1st one but when I do a uname -a I get the NON xen enabled kernel. I know I am doing something stupid but if anybody has any... (1 Reply)
Discussion started by: razor3928
1 Replies
6. Solaris
Hi,
I`m on SunFire480R with Solaris 10. Disk in rootdg group failed, so it was replaced. However, I cannot make Veritas initalise the replaced disk:
# vxdctl enable
# vxdisk list c1t0d0s2
Device: c1t0d0s2
devicetag: c1t0d0
type: auto
flags: online error private autoconfig... (1 Reply)
Discussion started by: masloff
1 Replies
7. Linux
Hi,
a little while ago, one of the GPT Partitioned hard disk had gone faulty in a Mirror RAID and is now successfully replaced.
here is how I did that.
1) created identical partition table on the new disk.
2) attached the mirrors using md commands.
The whole procedure is given below:... (2 Replies)
Discussion started by: busyboy
2 Replies
8. HP-UX
Scenario1:
VG00 lvm,not mirrored,2 disk of 36GB vg size
VG00 size is under 30G.
Is possible to remove a disk of 36GB and replace "on fly"
with a disk of 300GB on VG00?
Thanks (6 Replies)
Discussion started by: Linusolaradm1
6 Replies
9. UNIX for Advanced & Expert Users
I am having trouble with LVM and one of my physical volumes.
Using Ubuntu Desktop 14.04
I was trying to set up LVM across two disks (not containing the OS or Home).
First I created the initial Physical Volume, the Volume Group, and the Logical volume, and everything seemed fine. The... (2 Replies)
Discussion started by: JR_ULFOR
2 Replies
10. AIX
OSLevel: 5300-10-02-0943
System Model: IBM,8203-E4A
Power 6
==
Hi!
I replaced a failed pdisk in the raid enclosure as follows,
- rmdev -l 'pdisk18' '-d'
- Replaced it.
- cfgmgr (detected)
- I can see the new drive, with the correct serial #
lscfg -v -l pdisk18
pdisk18... (2 Replies)
Discussion started by: estrar
2 Replies
fddisk(8) System Manager's Manual fddisk(8)
NAME
fddisk - FDI disk maintenance utility
SYNOPSIS
/sbin/fddisk options special
OPTIONS
Unless this option is specified, an attempt to format or to install a file system fails in two cases. The first failure occurs when the
device has been opened since the media was inserted. The second failure occurs if the device is currently opened by another process. For-
mats the media to the density appropriate for that media. Copies a hex dump of sector number PSN to stdout. Uses the interleave factor
nnn for formatting. If specified, ccc indicates an additional intercylinder interleave. Copies a packed-C hex dump of the entire disk to
stdout. Specifies silent mode. This option blocks informational messages from appearing on stderr. Reads the entire media. The command
fails if the utility finds a bad sector. Waits for media to be inserted into the drive if none is present. Waits for new media to be
inserted into the drive if none is present or if the current media has been opened since it was last inserted. Reads the disk and reports
on the format of the disk.
OPERANDS
Specifies an unmounted, raw device pathname. This device must be an FDI interface (fd).
DESCRIPTION
The fddisk utility, an FDI (integrated Floppy Disk Interface) disk maintenance program, can format a floppy disk, scan a floppy disk for
bad blocks, and read and write selected blocks. It can be used in shell scripts for checking the status of floppy disks. Such status
checks include checking for or waiting for the presence of media, and checking for or waiting for the user to change the media.
RESTRICTIONS
The fddisk utility has the following restrictions: You must have read/write access to the device. The device must not be mounted. The
program can only be used with a 3.5-inch floppy disk in the RX26 drive. In some cases, it might not be possible to format a floppy disk at
a higher density than it is already formatted. If this situation occurs, the floppy disk must be bulk erased before it can be reformatted
at a higher density.
EXAMPLES
This example formats a floppy disk in drive zero: # /sbin/fddisk -fmt /dev/rdisk/floppy0a This example formats a floppy disk in drive zero
when the disk has been read or written since it was inserted into the drive: # /sbin/fddisk -fmt -f /dev/rdisk/floppy0a
SEE ALSO
Commands: mount(8), restore(8), uerf(8)
Files: fd(7)
fddisk(8)