10-10-2013
"Theoretically" you could have more than 120 LDOMs (as your server has 128 processor threads), but performance on each of them would be very low.
9 More Discussions You Might Find Interesting
1. Shell Programming and Scripting
now, what do you define as core files.
there are some files outthere with the name perl.core, I-core.png, core.png
I mean, are these classified as core files too??? i thought core files are simply files called "core". Please help me out
this is urgent (2 Replies)
Discussion started by: TRUEST
2 Replies
2. Solaris
Setting up a T5240 with two disks c1t0d0 and c1t1d0.
I am trying to use raidctl but when I issue.
raidctl -l
I get
Controller 1
Disk: 0.0.0
Disk: 0.1.0
So I try
raidctl -c '0.0.0 0.1.0' -r 1 1
and I get "Array in use."
I try (4 Replies)
Discussion started by: photon
4 Replies
3. Solaris
its a fresh installation. during the OS setup, it did not prompt for IP, netmask and gateway. using Solaris 10 08/07 update 4. I tried to plumb manually but encountered no such interface error. but nxge interfaces can be greped from the /etc/path_to_inst file.
getting similar error on... (3 Replies)
Discussion started by: incredible
3 Replies
4. Solaris
Hi,
We are planning to buy new server for our data center. Sun T5240 or M3000 which one have better performance, we are going to create many dt sessions in this server. So, i need your suggestions.
RJS (4 Replies)
Discussion started by: rajasekg
4 Replies
5. Solaris
Hi Friends
we have sun T5240 server, we have taken ufsdump of this server remotely with scsi tapedrive, If we need to do ufsrestore means what we have to do, since T5240 has not having scsi port, any procedure is there?
Regards
Rajasekar (5 Replies)
Discussion started by: rajasekg
5 Replies
6. Solaris
Hi Gurus
Can any one tell me the process of disabling the multithreading option on T5240 server and my OS is on LDOM, having one physical processor with 8 core & 8 thread per core
Regards (3 Replies)
Discussion started by: amity
3 Replies
7. Solaris
Hi !
I've been given a T5240 with 4 disks and 2 HBA cards (but no array connected). I did a factory reset on SP and NVRAM clean on OBP because the server had been used before.
I boot cdrom in single mode and try to create a hw mirror with disks from c1... but only c2 is seen by raidctl.
... (2 Replies)
Discussion started by: delavega
2 Replies
8. Solaris
Hi
I need to reduce cores on T5240 server for meeting Oracle Core licenses. For that I have install the LDOM packages & run below mention commands.
bash-3.2# ldm list-config
factory-default
config_initial
bash-3.2# ldm set-vcpu 32 primary
bash-3.2# ldm list-config... (5 Replies)
Discussion started by: amity
5 Replies
9. Solaris
Hi Folks,
Just a quick question - hopefully!
I have an application currently running on a V890 with Solaris 9, I'd like to move this to either one of our T-5's or one of the T5240's in a Legacy container on an LDOM - but the fly in the ointment is the application still uses a standard Hayes... (3 Replies)
Discussion started by: gull04
3 Replies
psradm(8) System Manager's Manual psradm(8)
NAME
psradm, offline, online - Stops and starts processors in a multiprocessor system
SYNOPSIS
/usr/sbin/psradm -f [-v] [[-a] [processor_id...]]
/usr/sbin/psradm -n [-v] [[-a] [processor_id...]]
/usr/sbin/online [-v] [processor_id...]
/usr/sbin/offline [-v] [processor_id...]
OPTIONS
The following options apply only to the psradm command: Specifies that all the processors except the master processor be put off line or on
line. Puts the specified processor off line. Puts the specified processor on line.
The following option applies to all forms of the command: Displays a message about the status of the operation performed on each processor.
DESCRIPTION
On a multiprocessor system, the psradm command puts one or more processors off line (stops a processor) or on line (starts a processor).
The processor_id variable specifies an integer that uniquely identifies a processor. Use the psrinfo command to display processor identi-
fication numbers.
The offline command puts one or more processors off line (stops a processor). If no processors are specified, all processors that are on
line are stopped except the master processor.
The online command puts one or more processors on line (starts a processor). If no processors are specified, all processors that are off
line are started.
Note that you cannot use these commands to start or stop the master processor in a multiprocessor system.
You must be the root user to use this command.
The /var/adm/wtmp file contains information about successful processor state transitions.
RESTRICTION
Do not use the psradm command to disable CPUs when benchmarking performance, because the command does not provide an accurate reflection of
the performance of a system that actually has fewer CPUs. Accurate performance results are obtained only when you disable the CPUs at the
SRM console command level.
EXAMPLES
The following command puts processors 2 and 3 off line: # psradm -f 2 3 The following command puts all the processors on line: # psradm -n
-a The following command puts all processors on line: # online -v
FILES
SEE ALSO
Commands: pset_info(1), psrinfo(1)
Files: processor_sets(4)
psradm(8)