10-10-2013
How much memory do you have? What's your expected workload? What kind of performance does your application require? These questions are more relevant than the theoretical number of possible ldoms. The theoretical number is likely in the hundreds, but in the real world other limitations will come into play that make that unattainable.
9 More Discussions You Might Find Interesting
1. Shell Programming and Scripting
now, what do you define as core files.
there are some files outthere with the name perl.core, I-core.png, core.png
I mean, are these classified as core files too??? i thought core files are simply files called "core". Please help me out
this is urgent (2 Replies)
Discussion started by: TRUEST
2 Replies
2. Solaris
Setting up a T5240 with two disks c1t0d0 and c1t1d0.
I am trying to use raidctl but when I issue.
raidctl -l
I get
Controller 1
Disk: 0.0.0
Disk: 0.1.0
So I try
raidctl -c '0.0.0 0.1.0' -r 1 1
and I get "Array in use."
I try (4 Replies)
Discussion started by: photon
4 Replies
3. Solaris
its a fresh installation. during the OS setup, it did not prompt for IP, netmask and gateway. using Solaris 10 08/07 update 4. I tried to plumb manually but encountered no such interface error. but nxge interfaces can be greped from the /etc/path_to_inst file.
getting similar error on... (3 Replies)
Discussion started by: incredible
3 Replies
4. Solaris
Hi,
We are planning to buy new server for our data center. Sun T5240 or M3000 which one have better performance, we are going to create many dt sessions in this server. So, i need your suggestions.
RJS (4 Replies)
Discussion started by: rajasekg
4 Replies
5. Solaris
Hi Friends
we have sun T5240 server, we have taken ufsdump of this server remotely with scsi tapedrive, If we need to do ufsrestore means what we have to do, since T5240 has not having scsi port, any procedure is there?
Regards
Rajasekar (5 Replies)
Discussion started by: rajasekg
5 Replies
6. Solaris
Hi Gurus
Can any one tell me the process of disabling the multithreading option on T5240 server and my OS is on LDOM, having one physical processor with 8 core & 8 thread per core
Regards (3 Replies)
Discussion started by: amity
3 Replies
7. Solaris
Hi !
I've been given a T5240 with 4 disks and 2 HBA cards (but no array connected). I did a factory reset on SP and NVRAM clean on OBP because the server had been used before.
I boot cdrom in single mode and try to create a hw mirror with disks from c1... but only c2 is seen by raidctl.
... (2 Replies)
Discussion started by: delavega
2 Replies
8. Solaris
Hi
I need to reduce cores on T5240 server for meeting Oracle Core licenses. For that I have install the LDOM packages & run below mention commands.
bash-3.2# ldm list-config
factory-default
config_initial
bash-3.2# ldm set-vcpu 32 primary
bash-3.2# ldm list-config... (5 Replies)
Discussion started by: amity
5 Replies
9. Solaris
Hi Folks,
Just a quick question - hopefully!
I have an application currently running on a V890 with Solaris 9, I'd like to move this to either one of our T-5's or one of the T5240's in a Legacy container on an LDOM - but the fly in the ointment is the application still uses a standard Hayes... (3 Replies)
Discussion started by: gull04
3 Replies
gcore(1) General Commands Manual gcore(1)
NAME
gcore - get core images of running processes
SYNOPSIS
filename] process-id...
DESCRIPTION
The command creates a core image of each specified process. By default, the name of the core image file for process-id will be The process
information in the core file can be obtained by using debuggers.
When the command creates a core image of each specified process, the process is temporarily stopped. Further, when the creation of core
image is complete, the process continues to execute.
Options
Creates the core file with name of the file as
If multiple process-id values are specified, filename will be common for all the core image files. See the section.
Operands
process-id The process ID for which a core image file will be created.
RETURN VALUE
Upon completion, exits with one of the following values:
A core file was successfully created.
An error condition was encountered.
In such a case, the creation of a core file is not guaranteed. The error conditions could be because of
o A nonexistent or incorrect process ID was specified.
o An invalid option was specified.
o The current working directory of the process or directory from which was invoked had no write permissions.
o The current working directory of the process was not accessible.
o The file system is full.
EXAMPLES
Example 1
Dump the core image of process 1030 in the file "core.1030".
Example 2
Dump the core image of the process 1030 in the file "test.1030".
Example 3
Dump the core image of the processes 1030, 1031, 1032, and 1033 in the files "core.1030", "core.1031", "core.1032", "core.1033".
Example 4
Dump the core image of the processes 1030, 1031, 1032, and 1033 in the files
FILES
Core image file for process-id. (Both where is invoked and the current working directory of the process.)
AUTHOR
was developed by Chris Bertin (HP).
SEE ALSO
adb(1), gdb(1), kill(1), ttrace(2), a.out(4), core(4).
gcore(1)