Sponsored Content
Operating Systems Linux Red Hat Regarding connecting to internet from RHEL 5 server Post 302861531 by jegaraman on Wednesday 9th of October 2013 06:04:57 AM
Old 10-09-2013
Dear Scott,

Pl find the below details.....

Code:
1.cat /etc/resolv.conf
search localdomain
nameserver      xxx.30.3.1
2.cat /etc/sysconfig/network-scripts/ifcfg-eth0
# Intel Corporation 82576 Gigabit Network Connection
DEVICE=eth0
BOOTPROTO=none
BROADCAST=xxx.30.7.191
HWADDR=00:21:28:E7:93:32
IPADDR=xxx.30.7.163
NETMASK=255.255.255.192
NETWORK=xxx.30.7.128
ONBOOT=yes
GATEWAY=xxx.30.7.190
TYPE=Ethernet
USERCTL=no
IPV6INIT=no
PEERDNS=yes
 
3.cat network
NETWORKING=yes
NETWORKING_IPV6=no
HOSTNAME=sun2

I am running RHEL on a physical server .

Thanks and Regards
Rj

Moderator's Comments:
Mod Comment Please use code tags
 

10 More Discussions You Might Find Interesting

1. IP Networking

connecting to internet

I have installed Solaris 8.0 and want to find out how can I go in and change my network setup and external IP setup. At the moment system running but I can not connect to the internet. But my lan card shows that I am on the network. I also get some advice that I should check the $Socks but how do I... (1 Reply)
Discussion started by: Cdrive
1 Replies

2. UNIX for Dummies Questions & Answers

Connecting to the Internet

Im on XP now but when im on linux how do I connect to the internet? I don't think AOL works with it but are there any free programs that I can use with it? (8 Replies)
Discussion started by: NoPepsiForYou
8 Replies

3. UNIX for Dummies Questions & Answers

Connecting to the Internet

Hi all, Is it possible (as I only have dial-up) to utilise my existing WinXP PC as a gateway to the internet for my 2nd PC (RH 8.0)?? .So connect with XP and have RH use a network connection (I guess) through the XP box and to the internet. If so, could I please have some links thrown my... (1 Reply)
Discussion started by: Cameron
1 Replies

4. UNIX for Dummies Questions & Answers

Need help connecting to the internet with solaris10

I am using solaris 10 with pentium 3. I have two network cards but none of them come up when i run <ifconfig -a> in command line. The two cards I have are : Linksys LNE 100TX and Netgear FA311. Does solaris 10 support these NICs or do I have to dowload the drivers for them. If so, can anyone... (1 Reply)
Discussion started by: fidjouss
1 Replies

5. Linux

connecting to INTERNET

Hi, I can ping www.yahoo.com (then domain name server is OK) but I can not navigate by Motzila to www.yahoo.com or any other Web Site. What can be the problem ? Mozila is configured in preference /advance to go automaticaly on WEB. We are under RED HAT AS3. What should I check ? Many thanks... (1 Reply)
Discussion started by: big123456
1 Replies

6. UNIX for Dummies Questions & Answers

Connecting to the Internet

I have just installed Linux and everything looks great, but how do I get my browser (Mozilla) to connect to my internet service provider? I have a cable connection to Bigpond in Australia, if that means anything - the ISP will not provide support for Linux. Your help would be greatly... (2 Replies)
Discussion started by: openhead
2 Replies

7. IP Networking

can i force connecting to local web server via internet network ?

Hello all this is general question , if i have web server installed in my local pc and i have client that connecting to that web server can i force it always to go via the internet network ? the reason im asking is .. that im noticed when i close my internet connection i still can connect to my... (2 Replies)
Discussion started by: umen
2 Replies

8. Solaris

connecting to internet from solaris 10

hi there, hope your chakras are all doing well :-) just installed solaris 10 on my laptop, all seems fine except the internet. How can i connect on a DSL line?. spent 7 days and 3 nights trying but couldnt find the starting point.... alikun (22 Replies)
Discussion started by: alikun
22 Replies

9. UNIX for Dummies Questions & Answers

Problems connecting to the Internet

I am trying to connect a Solaris 10 PC to the internet via a Linksys router and a cable modem. I have tried following suggestions in one of the posts here for manual setup but so far no luck. Does the Solaris 10 install for x86 automatically pick up the internet connection? Dave :>) (4 Replies)
Discussion started by: dohling
4 Replies

10. SCO

Connecting to the internet

Hi, I have a router, 192.168.1.1, and an internet router, 10.0.0.138. I have connected the server to the 1st router and assigned it a IP address of 192.168.1.1. I can ping both routers successfully but I have no access to internet. Any suggestions? sco5.0.7 (11 Replies)
Discussion started by: juan.navarrete
11 Replies
MSSQL_CONNECT(3)														  MSSQL_CONNECT(3)

mssql_connect - Open MS SQL server connection

SYNOPSIS
resource mssql_connect ([string $servername], [string $username], [string $password], [bool $new_link = false]) DESCRIPTION
mssql_connect(3) establishes a connection to a MS SQL server. The link to the server will be closed as soon as the execution of the script ends, unless it's closed earlier by explicitly calling mssql_close(3). PARAMETERS
o $servername - The MS SQL server. It can also include a port number, e.g. hostname:port (Linux), or hostname,port (Windows). o $username - The username. o $password - The password. o $new_link - If a second call is made to mssql_connect(3) with the same arguments, no new link will be established, but instead, the link identifier of the already opened link will be returned. This parameter modifies this behavior and makes mssql_connect(3) always open a new link, even if mssql_connect(3) was called before with the same parameters. RETURN VALUES
Returns a MS SQL link identifier on success, or FALSE on error. CHANGELOG
+--------+------------------------------------+ |Version | | | | | | | Description | | | | +--------+------------------------------------+ | 5.1.0 | | | | | | | The $new_link parameter was added | | | | +--------+------------------------------------+ EXAMPLES
Example #1 mssql_connect(3) example <?php // Server in the this format: <computer><instance name> or // <server>,<port> when using a non default port number $server = 'KALLESPCSQLEXPRESS'; // Connect to MSSQL $link = mssql_connect($server, 'sa', 'phpfi'); if (!$link) { die('Something went wrong while connecting to MSSQL'); } ?> SEE ALSO
mssql_close(3), mssql_pconnect(3). PHP Documentation Group MSSQL_CONNECT(3)
All times are GMT -4. The time now is 09:08 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy